CHECK MULTIPLEX NETWORK DOOR ECU
Disconnect the R18 and R19 multiplex network door ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R18-18 (IG) - Body ground | W - Body ground | IG power supply | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| R18-20 (ECUB) - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| R19-1 (B) - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| R19-10 (GND) - Body ground | W - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the R18 and R19 multiplex network door ECU connectors.
Measure the voltage and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*: w/ Hands Free Power Back Door |
||||
| R18-1 (DS1) - Body ground | L - Body ground | Power back door unit assembly LH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation
(See waveform 1) |
|||
| R18-2 (DS2) - Body ground | R - Body ground | Power back door unit assembly LH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation
(See waveform 2) |
|||
| R18-3 (DS12) - Body ground | V - Body ground | Power back door unit assembly RH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation
(See waveform 1) |
|||
| R18-4 (DS22) - Body ground | R - Body ground | Power back door unit assembly RH (door sensor) signal | Power back door not operating | 7 V or higher |
| Power back door operating | Pulse generation
(See waveform 2) |
|||
| R18-5 (DSV2) - Body ground | G - Body ground | Power back door unit assembly RH (door sensor) power supply | Always | 7 V or higher |
| R18-6 (OSR) - R18-24 (OSE) | SB - GR | Power back door sensor assembly RH signal | Power back door sensor assembly RH not pressed | 4 to 6 V |
| Power back door sensor assembly RH pressed | Below 1 V | |||
| R18-8 (BDDN) - Body ground | LG - Body ground | Back door control switch signal | Back door control switch on | Below 1 V |
| Back door control switch off | Pulse generation | |||
| R18-12 (LIB) - Body ground | W - Body ground | Back door lock signal | Back door is locked | Below 1 V |
| Back door is unlocked | 11 to 14 V | |||
| R18-14 (KSIN) - Body ground* | W - Body ground | Kick detection signal | Engine switch on (IG), kick door control sensor not detecting a foot → detecting a foot | Pulse generation
(See waveform 3) |
| R18-16 (BZR+) - Body ground | W - Body ground | Power back door warning buzzer signal | Power back door warning buzzer sounding | Pulse generation |
| Power back door warning buzzer not sounding | Below 1 V | |||
| R18-19 (DSG2) - Body ground | P - Body ground | Power back door unit assembly RH (door sensor) ground | Always | Below 1 V |
| R18-21 (DSG) - Body ground | P - Body ground | Power back door unit assembly LH (door sensor) ground | Always | Below 1 V |
| R18-25 (DSV) - Body ground | G - Body ground | Power back door unit assembly LH (door sensor) power supply | Always | 7 V or higher |
| R18-26 (OSL) - R18-24 (OSE) | L - GR | Power back door sensor assembly LH signal | Power back door sensor assembly LH not pressed | 4 to 6 V |
| Power back door sensor assembly LH pressed | Below 1 V | |||
| R19-4 (DC+) - R19-3 (DC-) | LA-B - LA-R | Back door lock assembly (back door lock motor) circuit | Back door lock motor operating | 11 to 14 V |
| Back door lock motor not operating | Below 1 V | |||
Using an oscilloscope, check waveform 1.
| Item | Condition |
|---|---|
| Tester Connection | ·
R18-1 (DS1) - Body ground ·
R18-3 (DS12) - Body ground |
| Tool setting | 2 V/DIV., 2 ms./DIV. |
| Vehicle condition | Power back door operating |
The period changes in accordance to the speed at which the power back door is opened and closed.
Using an oscilloscope, check waveform 2.
| Item | Condition |
|---|---|
| Tester Connection | ·
R18-2 (DS2) - Body ground ·
R18-4 (DS22) - Body ground |
| Tool setting | 2 V/DIV., 2 ms./DIV. |
| Vehicle condition | Power back door operating |
The period changes in accordance to the speed at which the power back door is opened and closed.
| *a | Kick detection signal |
Using an oscilloscope, check waveform 3.
| Item | Content |
|---|---|
| Tester connection | R18-14 (KSIN) - Body ground |
| Tool setting | 2 V/DIV., 50 ms./DIV. |
| Vehicle condition | Engine switch on (IG), kick door control sensor not detecting a foot → detecting a foot |
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
| *A | except LHD, Manual Transaxle | *B | for LHD, Manual Transaxle |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the instrument panel junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: for Manual Transaxle with Stop and Start System *2: except Manual Transaxle with Stop and Start System |
||||
| A-31 (BECU) - Body ground | None - Body ground | Battery power supply | Always | 11 to 14 V |
| A-30 (ACC) - Body ground | None - Body ground | ACC power supply | Engine switch on (ACC) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| A-32 (IG) - Body ground | None - Body ground | IG power supply | Engine switch on (IG) | 11 to 14 V*1
10.5 to 16 V*2 |
| Engine switch off | Below 1 V | |||
| A-11 (GND1) - Body ground | None - Body ground | Body ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Measure the voltage and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G43-13 (LSBO) - Body ground | G - Body ground | Back door lock signal | Back door is locked | Below 1 V |
| Back door is unlocked | 11 to 14 V | |||
| G45-4 (PBDS) - Body ground | G - Body ground | Power back door control switch signal | Power back door control switch off | Pulse generation |
| Power back door control switch on | Below 1 V |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)