Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM (for Gasoline Model)
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0376805 POWER BACK DOOR SYSTEM(for Gasoline Model) C

DOOR / HATCH  POWER BACK DOOR SYSTEM(for Gasoline Model)  B2250  Back Door Closer Operation Malfunction  


DESCRIPTION

The multiplex network door ECU receives signals from the latch switch, initial switch, pawl switch and back door courtesy switch, which are built into the back door lock with courtesy light switch assembly. Based on these switch signals, the latch position of the back door lock with courtesy light switch assembly is determined.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2250 Back Door Closer Operation Malfunction While the back door closer is operating, a malfunction is detected in position information from the initial switch within a specified amount of time.
·

back door lock with courtesy light switch assembly

·

Harness or connector

·

Multiplex network door ECU



WIRING DIAGRAM

E408602E01
4.969,1.927 5.427,2.125 0.458,0.198 10 false R18 4.99,0.76 5.448,0.958 0.458,0.198 10 false POS 4.969,2.094 6.76,2.333 1.792,0.24 10 false Multiplex Network Door ECU 4.74,0.646 4.896,0.844 0.156,0.198 10 false 7 3.031,0.646 3.188,0.844 0.156,0.198 10 false 6 3.042,1.344 3.198,1.542 0.156,0.198 10 false 1 2.563,0.896 3.021,1.094 0.458,0.198 10 false OPN 1.281,0.938 3.427,1.135 2.146,0.198 10 false Initial Switch 2.74,1.563 2.896,1.76 0.156,0.198 10 false E 0.365,1.833 0.823,2.031 0.458,0.198 10 false R14 0.365,2 3.885,2.198 3.521,0.198 10 false Back Door Lock with Courtesy Light Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Closer Position SW Initial switch signal ON or OFF ON: Back door lock sector gear in center position (Initial switch on)
OFF: Back door lock sector gear out of center position (Initial switch off)
-
Body Electrical > Back Door > Data List
Tester Display
Closer Position SW
50003 159 3
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY
2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY
a.

Remove the back door lock with courtesy light switch assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock with courtesy light switch assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the R14 back door lock with courtesy light switch assembly connector.


b.

Disconnect the R18 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R14-6 (OPN) - R18-7 (POS) Always Below 1 Ω
R14-1 (E) - Body ground Always Below 1 Ω
R14-6 (OPN) or R18-7 (POS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR