Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit between terminal ACCD of the certification ECU (smart key ECU assembly) and the ACC relay.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction The ACC relay circuit of the certification ECU (smart key ECU assembly) is malfunctioning. (1-trip detection logic*)
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

Instrument panel junction block assembly (ACC relay)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


DTC Output Confirmation Operation:

Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the ACC relay being stuck on, the ACC relay does not turn off even though the power switch is off.

·

If there is a malfunction due to the ACC relay being stuck off, the ACC relay does not turn on even though the power switch is on (ACC).


HINT:

The power switch can be turned on (IG) and the hybrid control system can be started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2274
Power Source Control
·

ACC Relay Monitor



WIRING DIAGRAM

E414767E03
2.063,4.115 4.875,4.885 2.813,0.771 10 false Instrument Panel Junction Block Assembly 5.5,3.833 7.094,4.865 1.594,1.031 10 false Certification ECU (Smart Key ECU Assembly) 5.479,3.625 6.271,4.448 0.792,0.823 10 false G54 6.094,2.729 6.563,3.25 0.469,0.521 10 false 16 6.354,2.854 6.938,3.406 0.583,0.552 10 false ACCD 5.344,2.823 5.927,3.375 0.583,0.552 10 false 4A 5.365,2.646 5.948,3.198 0.583,0.552 10 false 30 5.302,1.823 5.885,2.375 0.583,0.552 10 false 4K 5.323,1.635 5.906,2.188 0.583,0.552 10 false 1 4.344,3.125 5.615,3.594 1.271,0.469 10 false ACC 3.073,2.656 4.344,3.125 1.271,0.469 10 false ECU-ACC 1.635,2.313 2.219,2.865 0.583,0.552 10 false 40 1.615,2.479 2.198,3.031 0.583,0.552 10 false 4A 1.615,2.833 2.198,3.385 0.583,0.552 10 false 4D 1.667,2.667 2.25,3.219 0.583,0.552 10 false 3 2.052,1.219 2.719,2.479 0.667,1.26 10 false SFT LOCK-ACC 3.25,0.5 4.844,1.531 1.594,1.031 10 false from Auxiliary Battery 0.156,2.313 1.406,3.531 1.25,1.219 10 false to Each ACC power supply 2.063,1.906 2.771,3.104 0.708,1.198 10 false P/OUTLET NO.1 2.938,1.771 5.167,2.99 2.229,1.219 10 false to Power outret socket assembly ACC power supply 2.906,1.042 5.25,2.302 2.344,1.26 10 false to Shift lock cantrol unit assembly ACC power supply

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)
a.

Disconnect the 4A, 4D and 4K instrument panel junction block assembly connectors.


b.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-16 (ACCD) - 4A-30 Always Below 1 Ω
4D-3 - Body ground Always Below 1 Ω
G54-16 (ACCD) or 4A-30 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B498244C38
1.604,0.115 1.969,0.354 0.365,0.24 1.125,1.99 1.292,1.99 1.292,1.99 1.292,0.969 true 1.667,0.167 2.01,0.365 0.344,0.198 10 false G54 0.719,1.917 1.313,2.115 0.594,0.198 10 false ACCD 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-16 (ACCD) - Body ground Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)