Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM (for HV Model)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0379921 OCCUPANT CLASSIFICATION SYSTEM(for HV Model) C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM(for HV Model)  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The passenger side buckle switch circuit consists of the occupant detection ECU and front seat inner belt assembly RH (front passenger side buckle switch).

DTC B1771 is stored when a malfunction is detected in the front passenger side buckle switch circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1771 Passenger Side Buckle Switch Circuit Malfunction
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the front passenger side buckle switch circuit.

·

Front passenger side buckle switch malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Front seat inner belt assembly RH (Front passenger side buckle switch)

·

Occupant detection ECU



WIRING DIAGRAM

C240591E33
0.542,3.073 2.885,3.448 2.344,0.375 10 false Front Seat Inner Belt Assembly RH (Front Passenger Side Buckle Switch) 5.344,3.073 7.052,3.448 1.708,0.375 10 false Occupant Detection ECU 5.344,2.906 5.823,3.177 0.479,0.271 10 false S21 5.219,0.813 5.563,1.281 0.344,0.469 10 false 7 5.219,1.979 5.51,2.25 0.292,0.271 10 false 9 1.844,0.813 2.188,1.26 0.344,0.448 10 false 1 1.844,1.979 2.625,2.469 0.781,0.49 10 false 2 0.542,2.906 0.99,3.146 0.448,0.24 10 false S20

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:
·

When DTC B1650 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1771 is output, perform troubleshooting for this DTC first.

·

If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt assembly RH.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

2.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.


b.

Check that the connectors (on the occupant detection ECU side and front seat inner belt assembly RH side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

3.CHECK FRONT SEAT WIRE RH

Connectors are deformed or damaged

3.CHECK FRONT SEAT WIRE RH
a.
C382236C04
0.844,0.635 1.302,0.906 0.458,0.271 0.26,3.688 0.719,3.958 0.458,0.271 1.573,4.292 1.813,4.292 true 0.927,0.688 1.594,0.896 0.667,0.208 10 false S21 0.333,3.74 0.948,3.938 0.615,0.198 10 false S20 0.833,0.188 1.146,0.385 0.313,0.198 10 false *a 0.156,3.219 0.469,3.417 0.313,0.198 10 false *b 1.833,4.219 2.198,4.438 0.365,0.219 10 false *4 0.677,2.74 1.042,2.958 0.365,0.219 10 false *1 2.427,2.667 2.792,2.885 0.365,0.219 10 false *2 1.5,2.51 1.865,2.729 0.365,0.219 10 false *3 2.135,2.344 2.5,2.563 0.365,0.219 10 false A 1.854,2.344 2.219,2.563 0.365,0.219 10 false B 1.24,2.344 1.604,2.563 0.365,0.219 10 false C 0.958,2.333 1.323,2.552 0.365,0.219 10 false D
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S21-7 - Body ground Power switch on (IG) Below 1 V
S21-9 - Body ground



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 and 2 of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S21-7 - S21-9 Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S21-7 - S21-9 Always 1 MΩ or higher
S21-7 - Body ground
S21-9 - Body ground



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

4.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 394

e.

Clear the DTCs stored in the airbag sensor assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 394
Result:
Proceed to
DTC B1771 is output
DTC B1771 is not output


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is output

5.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

DTC B1771 is not output

5.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt assembly RH with a new one.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle if possible.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG), and wait for at least 60 seconds.


c.

Clear the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 394

d.

Clear the DTCs stored in the airbag sensor assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 394
Result:
Proceed to
DTC B1771 is not output
DTC B1771 is output


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is not output

END (FRONT SEAT INNER BELT ASSEMBLY RH WAS DEFECTIVE)

DTC B1771 is output

7.REPLACE OCCUPANT DETECTION ECU
7.REPLACE OCCUPANT DETECTION ECU
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU with a new one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL


d.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


Result:
Proceed to
NEXT



NEXT

8.PERFORM ZERO POINT CALIBRATION
8.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)