This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2658 | Short in Sensor with Motor Power Supply Circuit | Problem with the voltage supplied to the position control sensor. | ·
Position control ECU assembly (driver seat) ·
Slide motor (front seat adjuster assembly [driver seat]) ·
Power seat tilt motor assembly (driver seat) ·
Power seat lifter motor assembly (driver seat) ·
Reclining motor (front seatback frame sub-assembly [driver Seat]) ·
Harness or connector |
Initializing the position control ECU assembly (driver seat) will clear the seat position memory.
Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>REGISTRATION
Clear the DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.
Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T8-26 (SSRS) - T1-2 | Always | Below 1 Ω |
| T8-26 (SSRS) or T1-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| T8-12 (SGND) - T1-3 | Always | Below 1 Ω |
| T8-12 (SGND) or T1-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-26 (SSRS) - S1-2 | Always | Below 1 Ω |
| S8-26 (SSRS) or S1-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| S8-12 (SGND) - S1-3 | Always | Below 1 Ω |
| S8-12 (SGND) or S1-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Rear view of wire harness connector
(to Slide Motor [Front Seat Adjuster Assembly (Driver Seat)]) |
Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| T1-2 - T1-3 | Slide switch on | 4.8 to 5.1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S1-2 - S1-3 | Slide switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.
Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T8-10 (SSFV) - T9-2 | Always | Below 1 Ω |
| T8-10 (SSFV) or T9-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| T8-12 (SGND) - T9-3 | Always | Below 1 Ω |
| T8-12 (SGND) or T9-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-10 (SSFV) - S9-2 | Always | Below 1 Ω |
| S8-10 (SSFV) or S9-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| S8-12 (SGND) - S9-3 | Always | Below 1 Ω |
| S8-12 (SGND) or S9-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Rear view of wire harness connector
(to Power Seat Tilt Motor Assembly [Driver Seat]) |
Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| T9-2 - T9-3 | Front vertical switch on | 4.8 to 5.1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S9-2 - S9-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.
Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T8-25 (SSRL) - T12-2 | Always | Below 1 Ω |
| T8-25 (SSRL) or T12-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| T8-12 (SGND) - T12-3 | Always | Below 1 Ω |
| T8-12 (SGND) or T12-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-25 (SSRL) - S12-2 | Always | Below 1 Ω |
| S8-25 (SSRL) or S12-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| S8-12 (SGND) - S12-3 | Always | Below 1 Ω |
| S8-12 (SGND) or S12-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Rear view of wire harness connector
(to Power Seat Lifter Motor Assembly [Driver Seat]) |
Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| T12-2 - T12-3 | Rear lifter switch on | 4.8 to 5.1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S12-2 - S12-3 | Rear lifter switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.
Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T8-11 (SSRR) - T23-2 | Always | Below 1 Ω |
| T8-11 (SSRR) or T23-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| T8-12 (SGND) - T23-3 | Always | Below 1 Ω |
| T8-12 (SGND) or T23-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-11 (SSRR) - S23-2 | Always | Below 1 Ω |
| S8-11 (SSRR) or S23-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| S8-12 (SGND) - S23-3 | Always | Below 1 Ω |
| S8-12 (SGND) or S23-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Rear view of wire harness connector
(to Reclining Motor [Front Seatback Frame Sub-assembly (Driver Seat)]) |
Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| T23-2 - T23-3 | Reclining switch on | 4.8 to 5.1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S23-2 - S23-3 | Reclining switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power seat tilt motor assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power seat lifter motor assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the slide motor (front seat adjuster assembly [driver seat]) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the reclining motor (front seatback frame sub-assembly [driver seat]) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG