The hybrid vehicle control ECU assembly detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P310711 | Lost Communication with Airbag System Control Module Circuit Short to Ground | Short to ground in the communication circuit:
Communication from the airbag sensor assembly stopped and Circuit Low has been detected for a certain period. (1 trip detection logic) |
·
Wire harness or connector ·
Airbag sensor assembly ·
Hybrid vehicle control ECU assembly |
Does not come on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P310711 | Airbag Status (Collision) |
After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 2 minutes or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Airbag system DTCs are not output. | A |
| Airbag system DTCs are output. | B |
Turn the power switch off.
A
B
w/ Occupant Classification System:
w/o Occupant Classification System:
Connect an oscilloscope between the hybrid vehicle control ECU assembly terminals specified in the table below.
Turn the power switch on (READY).
for LHD:
Measure the waveform.
| *A | for LHD | - | - |
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
- | - |
| Item | Contents |
|---|---|
| Terminal | A30-29 (ABFS) - A30-3 (E1) |
| Equipment Setting | 5 V/DIV., 150 ms./DIV. |
| Condition | Power switch on (READY) |
for RHD:
Measure the waveform.
| *A | for RHD | - | - |
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
- | - |
| Item | Contents |
|---|---|
| Terminal | G63-29 (ABFS) - G63-3 (E1) |
| Equipment Setting | 5 V/DIV., 150 ms./DIV. |
| Condition | Power switch on (READY) |
| Result | Proceed to |
|---|---|
| The waveform appears as shown in the illustration. | A |
| The waveform differs from the one shown in the illustration. | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P310711 is not output. | A |
| P310711 is output. | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G70 airbag sensor assembly connector.
| *a | Component without harness connected
(Airbag Sensor Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G70-24 (GSW2) - G70-33 (E1) | Power switch off | 10 kΩ or higher |
Reconnect the G70 airbag sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.
*1: for LHD
*2: for RHD
Disconnect the G70 airbag sensor assembly connector.
| *A | for LHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
for LHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-29 (ABFS) or G70-24 (GSW2) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *A | for RHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
for RHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G63-29 (ABFS) or G70-24 (GSW2) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the G70 airbag sensor assembly connector.
Reconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG