Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0373331 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Unlock Warning Switch Circuit  


DESCRIPTION

The key unlock warning switch assembly comes on when the ignition key is inserted into the ignition key cylinder and goes off when the ignition key is removed.

WIRING DIAGRAM

E352027E04
0.927,1.875 1.385,2.073 0.458,0.198 10 false G29 1.333,1.521 1.792,1.719 0.458,0.198 10 false UN- 2.26,1.521 2.719,1.719 0.458,0.198 10 false UN+ 3.719,1.615 4.177,1.813 0.458,0.198 10 false 4A 5.177,1.625 5.531,1.813 0.354,0.188 10 false A 5.49,1.49 5.906,1.677 0.417,0.188 10 false KSW 1.115,1.51 1.302,1.677 0.188,0.167 10 false 2 2.646,1.521 2.833,1.688 0.188,0.167 10 false 1 3.74,1.417 3.927,1.583 0.188,0.167 10 false 41 5.188,1.406 5.375,1.573 0.188,0.167 10 false 3 0.927,2.01 3.167,2.219 2.24,0.208 10 false Un-lock Warning Switch Assembly 3.625,2.229 5.271,2.667 1.646,0.438 10 false Instrument Panel Junction Block Assembly 5.313,2.438 6.958,2.823 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 6.063,1.156 6.479,1.344 0.417,0.188 10 false +B

PROCEDURE

1.READ VALUE USING GTS (KEY UNLOCK WARNING SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch ON or OFF ON: Key inserted into ignition key cylinder
OFF: Key removed from ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

When the key is in the ignition key cylinder, "ON" appears on the screen.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT UN-LOCK WARNING SWITCH ASSEMBLY
2.INSPECT UN-LOCK WARNING SWITCH ASSEMBLY
a.

Remove the un-lock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the un-lock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - UN-LOCK WARNING SWITCH ASSEMBLY - BODY GROUND)

NG

REPLACE UN-LOCK WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - UN-LOCK WARNING SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the 4A instrument panel junction block assembly connector.


b.

Disconnect the G29 un-lock warning switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-41 - G29-1 (UN+) Always Below 1 Ω
4A-41 or G29-1 (UN+) - Other terminals and body ground Always 10 kΩ or higher
G29-2 (UN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Measure the resistance according to the value(s) in the table below.

E352025C04
3.25,0.25 3.75,0.5 0.5,0.25 3.25,1.75 3.75,2 0.5,0.25 2.104,2.302 2.427,2.604 true 3.417,0.281 3.729,0.438 0.313,0.156 10 false 4A 3.469,1.781 3.781,1.938 0.313,0.156 10 false A 2.479,2.531 2.927,2.688 0.448,0.156 10 false KSW
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4A-41 - A-3 (KSW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG