43420G
1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
Install a new front drive shaft hole snap ring LH.
43420
2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
Coat the spline of the inboard joint shaft assembly with MP grease.
for Automatic Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota genuine ATF WS.
for Manual Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine Manual Transmission Gear Oil LV.
for CVT:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT fluid FE.
for Hybrid Vehicle Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine ATF WS.
Set the front drive shaft hole snap ring LH with the opening side facing down.
| *a | Cross Section of Front Drive Shaft Oil Seal LH |
|
MP Grease |
|
Toyota Genuine Oil Seal Side Lip Grease |
Coat the lip of the front drive shaft oil seal LH with MP grease and Toyota genuine oil seal side lip grease as shown in the illustration.
Apply a light coat of MP grease and Toyota genuine oil seal side lip grease to the entire circumference of the front drive shaft oil seal LH.
Align the splines and tap in the front drive shaft assembly with a brass bar and hammer.
Using MP grease, set the front drive shaft hole snap ring in the groove with the opening facing downwards and centered radially.
Be careful not to damage the oil seal, front axle inboard joint boot and front drive shaft dust cover.
43410
3.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
for Automatic Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota genuine ATF WS.
for Manual Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine Manual Transmission Gear Oil LV.
for CVT:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT fluid FE.
for Hybrid Vehicle Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine ATF WS.
| *a | Cross Section of Front Drive Shaft Oil Seal RH |
|
MP Grease |
|
Toyota Genuine Oil Seal Side Lip Grease |
Coat the lip of the front drive shaft oil seal RH with MP grease and Toyota genuine oil seal side lip grease as shown in the illustration.
Apply a light coat of MP grease and Toyota genuine oil seal side lip grease to the entire circumference of the front drive shaft oil seal RH.
Align the inboard joint splines, and securely insert the front drive shaft assembly RH.
Do not damage the front drive shaft oil seal RH.
Do not damage the front axle inboard joint boot.
Install the front drive shaft assembly RH with the 2 bolts.
| *a | Matchmark |
Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
Do not push the front axle assembly further out of the vehicle than is necessary.
Be careful not to damage the front axle outboard joint boot.
Check for any foreign matter on the speed sensor rotor and insertion part.
Do not damage the speed sensor rotor.
4.CONNECT STEERING KNUCKLE WITH AXLE HUB LH
|
Toyota Body Grease W |
Apply MP grease to the entire contact surface between the front drive shaft assembly and axle hub bearing surface or only apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of Toyota Body Grease W to the 4 areas on the axle hub bearing shown in the illustration.
Align the matchmarks and connect the steering knuckle with axle hub LH.
|
Hook |
Set the 2 front speed sensor LH hooks on the front shock absorber assembly LH.
Do not twist the front speed sensor when installing it.
Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.
Do not twist the front flexible hose when installing it.
Install the front speed sensor to the steering knuckle with the bolt.
Prevent foreign matter from attaching to the front speed sensor tip.
Firmly insert the front speed sensor body into the steering knuckle before tightening the bolt.
After installing the front speed sensor to the steering knuckle, make sure that there is no clearance between the front speed sensor stay and steering knuckle. Also make sure that no foreign matter is stuck between the parts.
Do not twist the front speed sensor when installing it.
Engage the clamp.
Do not twist the front speed sensor when installing it.
5.CONNECT STEERING KNUCKLE WITH AXLE HUB RH
Use the same procedure described for the LH side.
48069
6.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
7.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
48810
8.INSTALL FRONT STABILIZER LINK ASSEMBLY LH
48820B
9.INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
43502H
10.INSTALL FRONT AXLE SHAFT NUT LH
Install the front axle shaft nut LH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION
Stake the front axle shaft nut LH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION
43501H
11.INSTALL FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
12.ADD TRANSAXLE OIL
for Automatic Transaxle: Click hereGeneral>MAINTENANCE>UB80E AUTOMATIC TRANSAXLE FLUID>REPLACEMENT
for Manual Transaxle: Click hereGeneral>MAINTENANCE>EG62 MANUAL TRANSAXLE OIL>REPLACEMENT
for CVT: Click hereGeneral>MAINTENANCE>K120 CONTINUOUSLY VARIABLE TRANSAXLE FLUID>REPLACEMENT
for Hybrid Vehicle Transaxle: Click hereGeneral>MAINTENANCE>P710 HYBRID TRANSAXLE FLUID>REPLACEMENT
13.INSPECT FOR OIL LEAK
53737D
14.INSTALL FRONT FENDER APRON SEAL LH
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for A25A-FXS: Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for A25B-FXS: Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
53736E
15.INSTALL FRONT FENDER APRON SEAL RH
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for A25A-FXS: Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for A25B-FXS: Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
51420
16.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for A25A-FXS: Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for A25B-FXS: Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
17.INSTALL FRONT WHEEL
18.CHECK SPEED SENSOR SIGNAL
w/ Vacuum Brake Booster: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster)>TEST MODE PROCEDURE
w/o Vacuum Brake Booster: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE
19.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT