Home › Engine / Hybrid System › A25B-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2019.02
RM3620E _51 Engine / Hybrid System _080116 A25B-FXS ENGINE CONTROL _0389132 SFI SYSTEM C

A25B-FXS ENGINE CONTROL  SFI SYSTEM  P034011  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground  P034015  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open  


DESCRIPTION

The camshaft position sensor (for intake camshaft) (VV1 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The intake camshaft has a timing rotor for the camshaft position sensor. When the intake camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals. The ECM uses the pulse signals to determine the camshaft angle. Then the ECM uses this data to control fuel injection duration and injection timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground The camshaft position sensor (for intake camshaft) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake camshaft) circuit

·

Camshaft position sensor (for intake camshaft)

·

ECM


Comes on DTC stored SAE Code: P0342
P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open The camshaft position sensor (for intake camshaft) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake camshaft) circuit

·

Camshaft position sensor (for intake camshaft)

·

ECM


Comes on DTC stored SAE Code: P0343

A255508E19
0.104,0.042 0.708,0.198 0.604,0.156 10 5 V/DIV. 0.104,0.698 0.427,0.865 0.323,0.167 10 CH1 0.125,1.479 0.448,1.646 0.323,0.167 10 CH2 0.052,0.865 0.427,1.01 0.375,0.146 10 (VV1) 0.063,1.625 0.458,1.771 0.396,0.146 10 (EV1) 3.042,0.813 3.385,0.958 0.344,0.146 10 GND 3.042,1.583 3.385,1.729 0.344,0.146 10 GND 1.25,1.885 2,2.063 0.75,0.177 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 stands for the camshaft position sensor signal (for intake camshaft), and EV1 stands for the camshaft position sensor signal (for exhaust camshaft).



ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

If the output voltage transmitted by the camshaft position sensor (for intake camshaft) remains low or high, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor (for intake camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait for 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P034011 or P034015.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A436569E02
0.927,2.083 3.271,2.344 2.344,0.26 10 false C10 0.927,2.25 2.542,2.698 1.615,0.448 10 false Camshaft Position Sensor (for Intake Camshaft) 5.719,2.25 6.531,2.427 0.813,0.177 10 false ECM 5.063,2.25 5.875,2.427 0.813,0.177 10 false C45 5.479,0.833 6.292,1.01 0.813,0.177 10 false 1.5 kΩ 5.563,0.26 6.375,0.438 0.813,0.177 10 false 5 V 4.583,0.438 5.396,0.615 0.813,0.177 10 false 88 4.583,0.99 5.396,1.167 0.813,0.177 10 false 90 4.583,1.521 5.396,1.698 0.813,0.177 10 false 89 2.313,0.438 3.125,0.615 0.813,0.177 10 false 3 2.302,0.979 3.115,1.156 0.813,0.177 10 false 1 2.302,1.521 3.115,1.698 0.813,0.177 10 false 2 1.99,0.438 2.802,0.615 0.813,0.177 10 false VC 1.906,0.979 2.719,1.156 0.813,0.177 10 false VVI+ 1.927,1.51 2.74,1.688 0.813,0.177 10 false VVI- 4.844,0.969 5.656,1.146 0.813,0.177 10 false VV1+ 4.844,1.521 5.656,1.698 0.813,0.177 10 false VV1- 4.844,0.438 5.656,0.615 0.813,0.177 10 false VCV1

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A402448C95
0.26,1.104 0.667,1.354 0.406,0.25 0.76,1.833 1.365,1.458 false 2.76,1.833 2.021,1.458 false 1.74,1.958 1.74,1.469 false 0.208,0.167 0.583,0.438 0.375,0.271 10 false *a 0.344,1.146 0.719,1.417 0.375,0.271 10 false C10 0.417,1.76 0.792,2.031 0.375,0.271 10 false VVI+ 2.823,1.781 3.198,2.052 0.375,0.271 10 false VC 1.635,1.979 2.271,2.156 0.635,0.177 10 false VVI-
*a Front view of wire harness connector
(to Camshaft Position Sensor (for Intake Camshaft))


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C10-3 (VC) - Body ground Power switch on (IG) 4.5 to 5.5 V
C10-1 (VVI+) - Body ground Power switch on (IG) 3.0 to 5.0 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-3 (VC) - C10-1 (VVI+) Power switch off 1.425 to 1.575 kΩ
C10-2 (VVI-) - Body ground Power switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

NG

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-1 (VVI+) - C45-90 (VV1+) Always Below 1 Ω
C10-2 (VVI-) - C45-89 (VV1-) Always Below 1 Ω
C10-3 (VC) - C45-88 (VCV1) Always Below 1 Ω
C10-1 (VVI+) or C45-90 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C10-2 (VVI-) or C45-89 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
C10-3 (VC) or C45-88 (VCV1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR