Home › Engine / Hybrid System › A25B-FXS (ENGINE CONTROL) › ECM › 2019.02–2020.08
RM3620E _51 Engine / Hybrid System _080116 A25B-FXS ENGINE CONTROL _0389138 ECM A

A25B-FXS ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



PROCEDURE

Hide 1. PRECAUTION (for LITHIUM-ION BATTERY)

HV battery learning values are stored in the battery ECU assembly and ECM and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.

NOTICE:
·

Do not replace the battery ECU assembly and ECM at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.

·

Do not replace the battery ECU assembly or ECM with a used one from another vehicle.



a.

Procedure when replacing both battery ECU assembly and ECM:

i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

Replace either ECU.


iii.

Connect the cable to the negative (-) auxiliary battery terminal.


iv.

Turn the power switch on (READY) and wait for 5 minutes or more.


v.

Turn the power switch off and disconnect the cable from the negative (-) auxiliary battery terminal.


vi.

Replace the other ECU.


vii.

Connect the cable to the negative (-) auxiliary battery terminal.


viii.

Check that the power switch can be turned on (READY).

HINT:

If the battery ECU assembly and ECM are replaced at the same time without following the above procedure, replace either the battery ECU assembly and ECM with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.




Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD

Hide 65351A 4.REMOVE BATTERY HOLE COVER

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89661 6.REMOVE ECM

a.
A433221

Push in the locks on the 2 levers, raise the 2 levers, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



b.

Remove the bolt and detach the clamp.


c.
A424106

Remove the 2 nuts and bolt.


d.

Remove the ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.



Hide 89667E 7.REMOVE NO. 1 ECM BRACKET

a.
A424108

Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 8.REMOVE NO. 2 ECM BRACKET

a.
A424107

Remove the 2 screws and No. 2 ECM bracket from the ECM.