These DTCs are stored when a malfunction occurs in the telephone antenna.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1573 | Short in Telephone Antenna Circuit | No. 1 amplifier antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the power switch is on (IG).
(Short circuit) |
·
Telephone transceiver assembly ·
No. 1 amplifier antenna assembly ·
No. 4 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly |
| B15CB | Telephone Antenna Disconnected | No. 1 amplifier antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the power switch is on (IG).
(Open circuit) |
·
Telephone transceiver assembly ·
No. 1 amplifier antenna assembly ·
No. 4 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the No. 1 amplifier antenna assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
| *a | Component without harness connected
(No. 1 Amplifier Antenna Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 - 4a | Always | 4 to 11 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly) |
| *b | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the No. 4 antenna cord sub-assembly from the No. 1 amplifier antenna assembly connector.
Disconnect the No. 4 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4 - B-2 | Always | Below 1 Ω |
| A-4a - B-2a | Always | Below 1 Ω |
| A-4 or B-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the No. 3 antenna cord sub-assembly from the No. 4 antenna cord sub-assembly connector.
Disconnect the No. 3 antenna cord sub-assembly from the antenna cord sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-2 - C-2 | Always | Below 1 Ω |
| B-2a - C-2a | Always | Below 1 Ω |
| B-2 or C-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.
Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-2 - E-2 | Always | Below 1 Ω |
| C-2a - E-2a | Always | Below 1 Ω |
| C-2 or E-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.
Disconnect the No. 2 antenna cord sub-assembly from the telephone transceiver assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-2 - F-1(ANT1) | Always | Below 1 Ω |
| E-2a - F-1a | Always | Below 1 Ω |
| E-2 or F-1(ANT1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT