The hybrid vehicle control ECU assembly and compressor with motor assembly communicate via a direct line. Compressor control is stopped and this DTC is stored if communication information is cut off or abnormal information occurs.
This DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.
This DTC will be stored as a history DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1498 | Communication Malfunction (A/C Inverter Local) | ·
Diagnosis condition: Power switch on (READY) ·
Malfunction status: Error or open in communication line between the hybrid vehicle control ECU assembly and compressor with motor assembly or high-voltage power source shut off |
·
Harness or connector ·
Hybrid vehicle control ECU assembly ·
Compressor with motor assembly ·
HV air conditioning wire ·
CAN communication system ·
Hybrid control system |
Memorized |
Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.
Inspect the fuses for circuits related to this system before performing the following procedure.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.
Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.
Using the GTS, check if the CAN communication system is functioning normally.
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Check if hybrid control system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Disconnect the C52 compressor with motor assembly connector.
Disconnect the A29 hybrid vehicle control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C52-3 (DOUT) - A29-8 (LIN3) | Always | Below 1 Ω |
| C52-3 (DOUT) - A29-8 (LIN3) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Do not disconnect the connector on the high-voltage side.
| *a | Front view of wire harness connector
(to Compressor with Motor Assembly) |
Disconnect the compressor with motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C52-2 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C52-1 (IG1) - Body ground | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Disconnect the Z1 and Z2 HV air conditioning wire connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-2 (PB) - Z2-1 (ACPB) | Always | Below 1 Ω |
| Z1-1 (PE) - Z2-2 (ACPE) | Always | Below 1 Ω |
| Z1-2 (PB) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG