Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for A25B-FXS) › 2019.02–2020.08
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0388775 COMPRESSOR(for A25B-FXS) A

HEATING / AIR CONDITIONING  COMPRESSOR(for A25B-FXS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the compressor with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 4.REMOVE FRONT WHEEL RH

Hide 75601A 5.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure described as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>WHEEL OPENING MOULDING (for Front)>REMOVAL


Hide 53896B 6.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 7.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51441 8.REMOVE NO. 1 ENGINE UNDER COVER

Hide 76621D 9.REMOVE FRONT FENDER MUDGUARD RH (w/ Mudguard)

HINT:

Use the same procedure described as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>MUDGUARD>REMOVAL


Hide 53736E 10.REMOVE FRONT FENDER APRON SEAL RH

Hide 53875A 11.REMOVE FRONT FENDER LINER RH

Hide 88704 12.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 13.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88370 14.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY