The TRAIL mode signal will be sent to the hybrid vehicle control ECU assembly when the TRAIL mode switch (integration control and panel assembly) is operated. If the specified conditions are met, the system enters TRAIL mode and the vehicle will be driven using TRAIL mode. This signal is then transmitted from the hybrid vehicle control ECU assembly via CAN to the combination meter assembly to illuminate the TRAIL indicator.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: System Select / CAN Bus Check.
| Result | Proceed to |
|---|---|
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: System Select / Health Check.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs are output. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Data List / AUTO LSD Switch.
| Tester Display |
|---|
| Auto LSD Switch |
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition |
|---|---|---|---|
| Auto LSD Switch | TRAIL mode switch (integration control and panel assembly) condition | ON or OFF | TRAIL mode switch (integration control and panel assembly) being pushed and held:
ON TRAIL mode switch (integration control and panel assembly) not operated: OFF |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the TRAIL mode switch operation. | A |
| The GTS display does not change according to the TRAIL mode switch operation. | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COMBINATION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G32 TRAIL mode switch (integration control and panel assembly) connector.
| *a | Front view of wire harness connector
(to TRAIL Mode Switch (Integration Control and Panel Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G32-13 (GND) - Body ground | Always | Below 1 Ω |
Reconnect the G32 TRAIL mode switch (integration control and panel assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.
*1: for LHD
*2: for RHD
Disconnect the G32 TRAIL mode switch (integration control and panel assembly) connector.
| *A | for LHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to TRAIL Mode Switch (Integration Control and Panel Assembly)) |
for LHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-36 (ALSD) - G32-19 (B) | Always | Below 1 Ω |
| A30-36 (ALSD) or G32-19 (B) - Body ground | Always | 10 kΩ or higher |
| *A | for RHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to TRAIL Mode Switch (Integration Control and Panel Assembly)) |
for RHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G63-36 (ALSD) - G32-19 (B) | Always | Below 1 Ω |
| G63-36 (ALSD) or G32-19 (B) - Body ground | Always | 10 kΩ or higher |
Reconnect the G32 TRAIL mode switch (integration control and panel assembly) connector.
Reconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG