Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY) › from 2019.02
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0390716 HYBRID CONTROL SYSTEM(for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)  P0D2D1C  Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU assembly detects a VH sensor malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage sensor internal circuit malfunction
·

Voltage sensor malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction

Inverter with converter assembly malfunction



Air conditioning system malfunction

Compressor with motor assembly malfunction


DESCRIPTION

For a description of the inverter.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>P0D2D16

The signal line from the inverter voltage (VH) sensor is connected to the MG ECU, which is built into the inverter with converter assembly.

HINT:

The term "drive motor A" indicates the motor (MG2).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range Inverter voltage (VH) sensor performance malfunction:
When not boosting, difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is large and difference between "VH-Voltage after Boosting" and "Hybrid Battery Voltage" is large.
(1 trip detection logic)
·

Inverter with converter assembly

·

Air conditioning system


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0D2D1C
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Hybrid Battery Voltage

·

Boost Ratio

·

SMRG Status

·

SMRP Status

·

SMRB Status

·

Ready Signal



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY).

7.

With the shift lever in D, depress both the accelerator pedal and brake pedal at the same time to raise the "Hybrid Battery SOC" to a sufficient level.

8.

Move the shift lever to P, check that the engine is stopped and move the shift lever to N.

9.

Set the A/C for maximum cooling.

10.

Leave the vehicle for a few minutes.

HINT:

Confirm that the Data List item "Boost Ratio" is 0% when the accelerator pedal is not depressed. Check that the Data List items "VH-Voltage after Boosting" and "Hybrid Battery Voltage" are almost the same.


11.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

12.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P0D2D1C only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of motor generator control system in the tables below are output. C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P0AFC00 Hybrid/EV Battery Sensor Module
P0AFC96 Hybrid/EV Battery Sensor Module Component Internal Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
Motor generator control system P0A1B1F Generator Control Module Circuit Intermittent
P0A1A47 Generator Control Module Watchdog / Safety MC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Power source circuit malfunction Hybrid control system P0AFC16 Hybrid/EV Battery Sensor Module Circuit Voltage Below Threshold
Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U029A87 Lost Communication with Hybrid/EV Battery Sensor Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0B3B14 Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open
P0B4014 Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open
P0B4514 Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open
P0B4A14 Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open
P0B4F14 Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open
P0B5414 Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open
P0B5914 Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open
P0B5E14 Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open
P0B6314 Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open
P0B6814 Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open
P0B6D14 Hybrid/EV Battery Voltage Sensor "K" Circuit Short to Ground or Open
P0B7214 Hybrid/EV Battery Voltage Sensor "L" Circuit Short to Ground or Open
P308A13 Hybrid/EV Battery Voltage Sensor All Circuit Open
P0AFC62 Hybrid/EV Battery Sensor Module Signal Compare Failure
P308A12 Hybrid/EV Battery Voltage Sensor All Circuit Short to Auxiliary Battery
System malfunction Hybrid control system P0C7600 Hybrid/EV Battery System Discharge Time Too Long
Motor generator control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Above Threshold
P0E3116 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold

HINT:
·

P0D2D1C may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





e.

Turn the power switch off.



A

2.CHECK FOR VEHICLE CONTROL HISTORY (HYBRID CONTROL SYSTEM)

B

C

2.CHECK FOR VEHICLE CONTROL HISTORY (HYBRID CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History (RoB).

Powertrain > Hybrid Control > Utility
Tester Display
Vehicle Control History (RoB)
50005 397 1055

e.

Check for Vehicle Control History.

Result:
Result Proceed to
Vehicle Control History Code "X0523" is stored A
Vehicle Control History Code "X0523" is not stored B



f.

Turn the power switch off.



A

3.CHECK TIME STAMP

B

5.CHECK DTC OUTPUT (AIR CONDITIONER)
3.CHECK TIME STAMP
HINT:

By checking Time Stamp, the time and order in which DTCs were stored in an ECU can be checked.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Health Check.


e.

Select the systems for which to perform Health Check and check for time stamp data: Store All Data.


f.

Select "Yes" when "Do you want to store time stamp data?" is displayed.

HINT:

If "Yes" is not selected, time stamp data will not be stored.



g.

After Health Check has completed, select "Time Stamp Data" to display the Time Stamp screen.


h.

Select the "HV" from the drop-down list on the bottom of the Time Stamp screen.


i.

Check the trip count for DTC P0D2D1C.


j.

Check the trip count for Vehicle Control History Code "X0523".


Result:
Result Proceed to
Trip counts for DTC P0D2D1C and Vehicle Control History Code "X0523" are identical. A
Trip counts for DTC P0D2D1C and Vehicle Control History Code "X0523" are not identical. B


k.

Turn the power switch off.



A

4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

5.CHECK DTC OUTPUT (AIR CONDITIONER)
4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P0D2D1C.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
All of the following conditions are met:
·

"SMRG Status" is OFF at the time DTC confirmed.

·

"SMRP Status" is OFF at the time DTC confirmed.

·

"SMRB Status" is ON at the time DTC confirmed.

·

"Ready Signal" items are all OFF before and after DTC confirmed.


A
At least one of the following conditions is not met:
·

"SMRG Status" is OFF at the time DTC confirmed.

·

"SMRP Status" is OFF at the time DTC confirmed.

·

"SMRB Status" is ON at the time DTC confirmed.

·

"Ready Signal" items are all OFF before and after DTC confirmed.


B



e.

Turn the power switch off.



A

B

5.CHECK DTC OUTPUT (AIR CONDITIONER)
5.CHECK DTC OUTPUT (AIR CONDITIONER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Air Conditioner / Trouble Codes.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

d.

Check for DTCs.

Result:
Result Proceed to
DTC B1472 is not output A
DTC B1472 is output B



e.

Turn the power switch off.



A

6.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY

B

6.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
a.

Operate the compressor under the following conditions.

Item Item
Power switch On (READY)
A/C switch On
Blower speed HI
Temperature setting MAX COLD
Ambient temperature 25°C (77°F) or higher


b.

Turn the power switch off.


c.

Check that there is no abnormal noise from the compressor immediately after the power switch is turned off.

Result:
Result Proceed to
No abnormal noise. A
Abnormal noise is heard. B




A

B