Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY THERMISTOR (for NICKEL METAL HYDRIDE BATTERY) › 2019.02–2020.08
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0371636 HV BATTERY THERMISTOR(for NICKEL METAL HYDRIDE BATTERY) A

HYBRID / BATTERY CONTROL  HV BATTERY THERMISTOR(for NICKEL METAL HYDRIDE BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid battery thermistor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.


·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide G920R 5.REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A430759

Remove the 5 nuts.


b.
A430760C01
0.771,1.938 0.938,1.938 0.938,1.938 1.115,1.781 false 2.521,2.01 2.333,2.01 2.333,2.01 1.969,1.604 true 0.604,1.854 0.917,2.052 0.313,0.198 10 false *1 2.563,1.938 2.875,2.135 0.313,0.198 10 false *2
*1 Rear No. 1 HV Battery Shield
*2 No. 2 Hybrid Battery Shield Sub-assembly
V113147

Pull Back


Pull back the rear No. 1 HV battery shield and remove the No. 2 hybrid battery shield sub-assembly from the HV battery.

HINT:

Pull back the rear No. 1 HV battery shield until it is separated from the stud bolt of the No. 2 hybrid battery shield sub-assembly.



Hide G92E1A 6.REMOVE NO. 1 HV BATTERY INTAKE DUCT LH

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A430761

Remove the clip to disconnect the No. 1 HV battery intake duct LH from the HV battery.


b.

Disengage the claw of hybrid battery thermistor (sensor portion) and remove the No. 1 HV battery intake duct LH.


Hide G9282 7.REMOVE HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A406103

Disengage the clamp.


b.
A406104

Disengage the 2 claws and remove the No. 1 hybrid battery packing from the HV battery.


c.
A430762

Disengage the clamp.


d.

Disconnect the battery voltage sensor connector.


e.
A406106

Disengage the 4 clamps.


f.
A406117

Disengage the 3 claws of the hybrid battery thermistor (sensor portions) and remove the hybrid battery thermistor from the HV battery.