Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › from 2019.02
RM3620E _55 Steering _077128 STEERING GEAR / LINKAGE _0377571 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  INSTALLATION  


PROCEDURE

Hide 45319 1.INSTALL STEERING GEAR HEAT INSULATOR (for RHD)

a.
C404138N01
0.844,1.167 1.031,1.375 0.188,0.208 10 true 1 1.969,1.583 2.177,1.792 0.208,0.208 10 false 2 1.854,0.052 2.021,0.219 0.167,0.167 10 true 3

Install the steering gear heat insulator to the rack and pinion power steering gear assembly with the 3 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 45470 2.TEMPORARILY INSTALL TIE ROD ASSEMBLY LH

a.
C404146C01
1.281,1.125 1.281,0.427 true 1.052,0.427 1.49,0.427 1.49,0.427 1.49,1.125 true 0.802,0.333 1.115,0.49 0.313,0.156 10 false *a
*a Matchmark


Install the lock nut and tie rod assembly LH to the rack and pinion power steering gear assembly until the matchmarks are aligned.

HINT:

After adjusting the toe-in, tighten the lock nut.



Hide 45460 3.TEMPORARILY INSTALL TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 44250 4.INSTALL RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.

Install the rack and pinion power steering gear assembly to the front frame assembly with the 4 bolts and 4 new nuts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 5.INSTALL FRONT STABILIZER BAR WITH BRACKET

a.

Install the front stabilizer bar with 2 front stabilizer links, front No. 1 stabilizer bracket LH, front No. 1 stabilizer bracket RH and 2 front No. 1 stabilizer bar bushings to the front frame assembly.


b.
C404156C01
2.042,0.729 2.156,0.24 2.156,0.24 2.25,0.24 true 2.292,0.146 2.604,0.302 0.313,0.156 10 false *a 0.979,1.844 1.156,2.031 0.177,0.188 10 true A 2.333,2.479 2.531,2.698 0.198,0.219 10 true B
*a Arrow
V100136

Front of the Vehicle


Install the front No. 1 stabilizer bracket LH to the front frame assembly with the 2 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Make sure to install the front No. 1 stabilizer bracket LH with its arrow facing the front of the vehicle.

·

Temporarily install the bolt (B) and then tighten the 2 bolts in the order of (A) and (B).




c.

Install the front No. 1 stabilizer bracket RH to the front frame assembly with the 2 bolts.

HINT:

Perform the same procedure as for the LH side.



Hide 7.CONNECT WIRE HARNESS (for LHD)

a.

Install the wire harness to the rack and pinion power steering gear assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C404157


b.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



Hide 8.CONNECT WIRE HARNESS (for RHD)

a.

Install the wire harness to the rack and pinion power steering gear assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C406971


b.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



Hide 45319 9.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

a.
C404137N01
2.396,0.094 2.552,0.292 0.156,0.198 10 true 1 0.792,1.229 0.99,1.448 0.198,0.219 10 true 2

Install the steering gear heat insulator to the rack and pinion power steering gear assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 45470 11.CONNECT TIE ROD ASSEMBLY LH

a.
C369776

Connect the tie rod assembly LH to the steering knuckle LH with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


Hide 45460 12.CONNECT TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45220 13.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C369775C01
0.958,2.823 1.531,2.823 true 1.115,2.833 1.115,2.906 1.115,2.906 1.469,2.906 true 0.792,2.74 0.958,2.906 0.167,0.167 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and rack and pinion power steering gear assembly.


b.

Connect the steering intermediate shaft assembly to the rack and pinion power steering gear assembly.


c.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 14.INSTALL FRONT WHEELS

Hide 15.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 45047 16.FULLY TIGHTEN TIE ROD END SUB-ASSEMBLY LH

a.
C422196C02
2.667,2.75 2.667,3.083 2.667,3.083 2.75,3.083 true 1.385,2.083 1.698,2.281 0.313,0.198 10 false *a 2.813,3.021 3.125,3.219 0.313,0.198 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the tie rod end sub-assembly lock nuts.

SST
09612-24014  (09617-24011)

Torque:
Specified Tightening Torque : 88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Make sure that the boots are not twisted.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52 mm (2.0472 in.)) + torque wrench (fulcrum length of 380 mm (14.9606 in.)):

77.4 N*m (789 kgf*cm, 57 ft.*lbf)




Hide 45046 17.FULLY TIGHTEN TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 18. TORQUE SENSOR ZERO POINT CALIBRATION