Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › from 2019.09
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0389152 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B1573  Short in Telephone Antenna Circuit  B15CB  Telephone Antenna Disconnected  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1573 Short in Telephone Antenna Circuit No. 1 amplifier antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Short circuit)
·

Telephone transceiver assembly

·

No. 1 amplifier antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly


B15CB Telephone Antenna Disconnected No. 1 amplifier antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Open circuit)
·

Telephone transceiver assembly

·

No. 1 amplifier antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly



WIRING DIAGRAM

E383187E13
4.01,4.958 5.188,5.844 1.177,0.885 10 false No. 1 Amplifier Antenna Assembly 5.635,2.156 7.021,3.052 1.385,0.896 10 false Telephone Transceiver Assembly 4.021,1.979 5.24,2.406 1.219,0.427 10 false No. 2 Antenna Cord Sub-assembly 2.24,1.979 3.427,2.438 1.188,0.458 10 false Antenna Cord Sub-assembly 0.531,4.969 1.708,5.385 1.177,0.417 10 false No. 3 Antenna Cord Sub-assembly 2.302,5 3.563,5.427 1.26,0.427 10 false No. 4 Antenna Cord Sub-assembly 3.656,4.031 4.844,5.021 1.188,0.99 10 false A 3.656,4.625 4.844,5.615 1.188,0.99 10 false A 1.938,4.021 3.125,5.01 1.188,0.99 10 false B 1.948,4.615 3.135,5.604 1.188,0.99 10 false B 5.354,0.99 6.542,1.979 1.188,0.99 10 false F 3.667,3.802 4.854,4.792 1.188,0.99 10 false 4 3.635,4.417 4.823,5.406 1.188,0.99 10 false 4a 1.958,3.823 3.146,4.813 1.188,0.99 10 false 2 1.917,4.396 3.104,5.385 1.188,0.99 10 false 2a 1.958,0.792 3.146,1.781 1.188,0.99 10 false 2 1.917,1.365 3.104,2.354 1.188,0.99 10 false 2a 3.656,0.802 4.844,1.792 1.188,0.99 10 false 2 3.625,1.375 4.813,2.365 1.188,0.99 10 false 2a 5.708,1 6.896,1.99 1.188,0.99 10 false ANT1 5.344,0.792 6.531,1.781 1.188,0.99 10 false 1 1.948,1.594 3.135,2.583 1.188,0.99 10 false C 3.646,1.583 4.833,2.573 1.188,0.99 10 false E 5.365,1.583 6.552,2.573 1.188,0.99 10 false F 3.646,0.979 4.833,1.969 1.188,0.99 10 false E 1.948,1 3.135,1.99 1.188,0.99 10 false C 5.344,1.406 6.531,2.396 1.188,0.99 10 false 1a

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY
2.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Remove the No. 1 amplifier antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C14
1.969,1.479 2.229,1.729 false 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.708 2.573,1.906 0.313,0.198 10 false 4a
*a Component without harness connected
(No. 1 Amplifier Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

3.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E389828C04
1.479,0.302 1.917,0.521 0.438,0.219 1.469,2.729 1.906,2.948 0.438,0.219 1.854,4.208 1.979,4.208 1.979,4.208 2.146,3.656 true 1.073,0.958 1.198,0.958 1.198,0.958 1.563,1.354 true 0.906,0.875 1.219,1.073 0.313,0.198 10 false 4a 1.656,4.125 1.969,4.323 0.313,0.198 10 false 2a 1.646,0.344 1.958,0.542 0.313,0.198 10 false A 1.635,2.771 1.948,2.969 0.313,0.198 10 false B 0.333,0.281 0.646,0.479 0.313,0.198 10 false *a 0.323,2.625 0.635,2.823 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the No. 4 antenna cord sub-assembly from the No. 1 amplifier antenna assembly connector.


b.

Disconnect the No. 4 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-2 Always Below 1 Ω
A-4a - B-2a Always Below 1 Ω
A-4 or B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

4.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E383188C01
1.469,2.365 1.875,2.604 0.406,0.24 1.469,0.427 1.875,0.667 0.406,0.24 1.271,3.375 1.594,3.979 1.594,3.979 1.719,3.979 true 1.281,1.5 1.604,2.083 1.604,2.083 1.729,2.083 true 1.625,0.469 2,0.708 0.375,0.24 10 false B 1.625,2.406 2,2.646 0.375,0.24 10 false C 1.792,2.01 2.167,2.25 0.375,0.24 10 false 2a 1.771,3.906 2.146,4.146 0.375,0.24 10 false 2a 0.313,0.302 0.625,0.458 0.313,0.156 10 false *a 0.406,2.24 0.719,2.396 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the No. 3 antenna cord sub-assembly from the No. 4 antenna cord sub-assembly connector.


b.

Disconnect the No. 3 antenna cord sub-assembly from the antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-2 Always Below 1 Ω
B-2a - C-2a Always Below 1 Ω
B-2 or C-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

5.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E385192C01
1.469,2.365 1.875,2.604 0.406,0.24 1.469,0.427 1.875,0.667 0.406,0.24 1.24,3.458 1.563,4.063 1.563,4.063 1.688,4.063 true 2.198,1.552 2.49,2.156 2.49,2.156 2.615,2.156 true 1.625,0.469 2,0.708 0.375,0.24 10 false C 1.625,2.406 2,2.646 0.375,0.24 10 false E 2.677,2.052 3.052,2.292 0.375,0.24 10 false 2a 1.75,3.958 2.125,4.198 0.375,0.24 10 false 2a 0.229,0.146 0.542,0.302 0.313,0.156 10 false *a 0.24,2.333 0.552,2.49 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


b.

Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - E-2 Always Below 1 Ω
C-2a - E-2a Always Below 1 Ω
C-2 or E-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

6.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E385665C01
1.615,2.354 2.052,2.615 0.438,0.26 1.583,0.417 2.021,0.677 0.438,0.26 2.25,1.469 2.375,2.063 2.375,2.063 2.51,2.063 true 1.99,3.5 2.406,3.156 2.406,3.156 2.542,3.156 true 1.76,3.552 1.25,3.042 1.25,3.042 1.094,3.042 true 1.75,0.458 1.906,0.656 0.156,0.198 10 false E 1.792,2.396 1.948,2.594 0.156,0.198 10 false F 2.563,1.99 2.833,2.24 0.271,0.25 10 false 2a 2.594,3.083 2.865,3.333 0.271,0.25 10 false 1a 0.396,0.208 0.708,0.365 0.313,0.156 10 false *a 0.427,2.24 0.74,2.396 0.313,0.156 10 false *b 0.719,2.969 1.396,3.375 0.677,0.406 10 false ANT1
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.


b.

Disconnect the No. 2 antenna cord sub-assembly from the telephone transceiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 - F-1(ANT1) Always Below 1 Ω
E-2a - F-1a Always Below 1 Ω
E-2 or F-1(ANT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT