Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › from 2019.02
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377694 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REASSEMBLY  


PROCEDURE

Hide 52463 1.INSTALL REAR BUMPER PAD LH

HINT:

When installing a new rear bumper pad LH, heat the rear bumper piece LH using a heat light.


Standard:
Item Temperature
Rear Bumper Piece LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper piece LH excessively.


a.

When reusing the rear bumper piece LH:

i.

Using a heat light, heat the rear bumper piece LH surface.


ii.

Remove any remaining double-sided tape from the rear bumper piece LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear bumper pad LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper piece LH surface.





b.
B524198C01
1.104,3.406 1.531,3.406 true 0.865,3.344 1.031,3.521 0.167,0.177 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear bumper piece LH on the installation area of the rear bumper pad LH using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper pad LH has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear bumper pad LH trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.
B523984C01
1.188,3.448 1.51,3.448 false 1.01,3.354 1.177,3.542 0.167,0.188 10 true *a
*a Mark-off Line


Align the rear bumper pad LH with the mark-off line on the rear bumper piece LH and install it.

HINT:

Press the rear bumper pad LH firmly to install it.



Hide 52463B 2.INSTALL REAR BUMPER PAD LH

HINT:

When installing a new rear bumper pad LH, heat the rear bumper piece LH using a heat light.


Standard:
Item Temperature
Rear Bumper Piece LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper piece LH excessively.


a.

When reusing the rear bumper piece LH:

i.

Using a heat light, heat the rear bumper piece LH surface.


ii.

Remove any remaining double-sided tape from the rear bumper piece LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear bumper pad LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper piece LH surface.





b.
B524197C01
0.927,3.458 1.323,3.458 true 0.667,3.365 0.865,3.583 0.198,0.219 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear bumper piece LH on the installation area of the rear bumper pad LH using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper pad LH has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear bumper pad LH trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.
B523983C01
0.979,3.458 1.333,3.458 false 0.792,3.375 0.969,3.542 0.177,0.167 10 true *a
*a Mark-off Line


Align the rear bumper pad LH with the mark-off line on the rear bumper piece LH and install it.

HINT:

Press the rear bumper pad LH firmly to install it.



Hide 52462 3.INSTALL REAR BUMPER PAD (for LH Side)

HINT:

When installing a new rear bumper pad, heat the rear bumper piece LH using a heat light.


Standard:
Item Temperature
Rear Bumper Piece LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper piece LH excessively.


a.

When reusing the rear bumper piece LH:

i.

Using a heat light, heat the rear bumper piece LH surface.


ii.

Remove any remaining double-sided tape from the rear bumper piece LH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear bumper pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper piece LH surface.





b.
B524194C01
2.135,3.406 2.448,3.406 true 2.5,3.323 2.688,3.51 0.188,0.188 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear bumper piece LH on the installation area of the rear bumper pad using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper pad has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear bumper pad trying not to touch the adhesional surface.


e.
B523982C05
2.135,3.333 2.448,3.333 true 2.49,3.25 2.677,3.438 0.188,0.188 10 true *a
*a Mark-off Line


Align the rear bumper pad with the mark-off line on the rear bumper piece LH and install it.

HINT:

Press the rear bumper pad firmly to install it.



Hide 52462 4.INSTALL REAR BUMPER PAD (for RH Side)

HINT:

When installing a new rear bumper pad, heat the rear bumper piece RH using a heat light.


Standard:
Item Temperature
Rear Bumper Piece RH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper piece RH excessively.


a.

When reusing the rear bumper piece RH:

i.

Using a heat light, heat the rear bumper piece RH surface.


ii.

Remove any remaining double-sided tape from the rear bumper piece RH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear bumper pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper piece RH surface.





b.
B524193C01
2.198,3.719 1.74,3.719 true 2.26,3.625 2.417,3.823 0.156,0.198 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear bumper piece RH on the installation area of the rear bumper pad using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper pad has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear bumper pad trying not to touch the adhesional surface.


e.
B524201C03
2.198,3.719 1.74,3.719 true 2.26,3.625 2.417,3.823 0.156,0.198 10 true *a
*a Mark-off Line


Align the rear bumper pad with the mark-off line on the rear bumper piece RH and install it.

HINT:

Press the rear bumper pad firmly to install it.



Hide 52462C 5.INSTALL REAR BUMPER PAD RH

HINT:

When installing a new rear bumper pad RH, heat the rear bumper piece RH using a heat light.


Standard:
Item Temperature
Rear Bumper Piece RH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper piece RH excessively.


a.

When reusing the rear bumper piece RH:

i.

Using a heat light, heat the rear bumper piece RH surface.


ii.

Remove any remaining double-sided tape from the rear bumper piece RH.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear bumper pad RH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper piece RH surface.





b.
B524192C01
1.917,3.302 2.313,3.302 true 2.354,3.208 2.542,3.396 0.188,0.188 10 true *a
*a Mark-off Line
V100144

Primer


Apply primer to the rear bumper piece RH on the installation area of the rear bumper pad RH using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper pad RH has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear bumper pad RH trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.
B524202C01
1.938,3.385 2.271,3.385 true 2.302,3.302 2.479,3.49 0.177,0.188 10 false *a
*a Mark-off Line


Align the rear bumper pad RH with the mark-off line on the rear bumper piece RH and install it.

HINT:

Press the rear bumper pad RH firmly to install it.



Hide 76829A 6.INSTALL BACK DOOR GARNISH RETAINER

a.
B524206

Install the back door garnish retainer.

HINT:

Use the same procedure for the RH and LH side.



Hide 52453 7.INSTALL REAR BUMPER CENTER GUARD (for Separate Type)

a.

Attach the guide and claw to install the rear bumper center guard.

B523975C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Install the 4 outside moulding retainers as shown in the illustration.

B524243


Hide 52461 8.INSTALL REAR BUMPER CENTER PAD (except Separate Type)

HINT:

When installing a new rear bumper center pad, heat the rear bumper cover using a heat light.


Standard:
Item Temperature
Rear Bumper Cover 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper cover excessively.


a.

When reusing the rear bumper cover:

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove any remaining double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear bumper center pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper cover surface.





b.

Apply primer to the rear bumper cover on the installation area of the rear bumper center pad using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper center pad has been attached.



B524147C01
1.177,1.615 1.177,1.281 true 3.552,1.604 3.552,1.271 true 5.906,1.635 5.906,1.302 true 1.104,1.656 1.417,1.854 0.313,0.198 10 false *a 3.469,1.635 3.781,1.833 0.313,0.198 10 false *a 5.823,1.635 6.135,1.833 0.313,0.198 10 false *a
*a Mark-off Line - -
V100144

Primer - -



c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new rear bumper center pad trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.

Align the 3 rear bumper center pads with the mark-off line on the rear bumper cover and install them.

HINT:

Press the rear bumper center pad firmly to install it.


B523978C01
1.26,1.521 1.26,1.271 false 3.531,1.521 3.531,1.271 false 5.844,1.552 5.844,1.302 false 1.177,1.542 1.354,1.708 0.177,0.167 10 true *a 3.438,1.542 3.615,1.708 0.177,0.167 10 true *a 5.771,1.573 5.948,1.74 0.177,0.167 10 true *a
*a Mark-off Line - -



Hide 81920 9.INSTALL REFLEX REFLECTOR ASSEMBLY LH

a.
B523985C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the reflex reflector assembly LH.


b.

Install the screw.


Hide 81910 10.INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:

Use the same procedure for the RH and LH side.


Hide 11.INSTALL SPRING NUT

a.
B524151C01
0,0 0,0 false
V113147

Install in this Direction


Install the 2 spring nuts.

HINT:

Use the same procedure for the RH and LH side.



b.

w/ Mudguard:

i.
B524031C01
0,0 0,0 false
V113147

Install in this Direction


Install the 2 spring nuts.

HINT:

Use the same procedure for the RH and LH side.




Hide 52162A 12.INSTALL REAR BUMPER PIECE LH

a.
B523986C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the rear bumper piece LH.


b.
B524242

Install the 3 outside moulding retainers as shown in the illustration.


c.

Install the 2 screws.


Hide 52161A 13.INSTALL REAR BUMPER PIECE RH

HINT:

Use the same procedure for the RH and LH side.


Hide 89348S 14.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89348R 15.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89342A 16.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89342 17.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 82182 18.INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

a.

Attach the clamp to install the No. 2 luggage room wire.

B523963C03
5.313,3.51 5.563,3.51 5.563,3.51 5.563,3.01 false 5.052,3.417 5.302,3.615 0.25,0.198 12 false *A
*A w/ Hands Free Power Back Door - -



b.

Connect the 4 connectors.

NOTICE:

Do not apply excessive loads to the retainer. Otherwise, it may peel off.



Hide 891B1 19.INSTALL KICK DOOR CONTROL BRACKET (w/ Hands Free Power Back Door)