Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › from 2019.02
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370877 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  INSTALLATION  


PROCEDURE

Hide 89305 1.INSTALL ULTRASONIC SENSOR CUSHION SET (w/ Parking Support Brake System)

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Install the ultrasonic sensor cushion set as shown in the illustration.

B549652C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 89348S 2.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

NOTICE:
·

Installing the rear center ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.



HINT:
·

Perform the following procedure only when replacement of a rear center ultrasonic sensor retainer is necessary.

·

Use the same procedure for the RH and LH side.

·

The following procedure is for the LH side.



a.

Clean the rear bumper assembly surface.

i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Wipe off any tape adhesive residue with cleaner.



b.
B502899C03
1.51,0.156 1.823,0.354 0.313,0.198 10 false *a 2.635,1.167 2.948,1.365 0.313,0.198 10 false *a
*a 30 mm (1.18 in.)


Cover the sensor installation hole from the outside of the rear bumper cover with a 30 mm (1.18 in.) square piece of tape.


c.

Apply primer to the rear bumper assembly on the installation area of the rear center ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear center ultrasonic sensor retainer has been attached.



B525256C01
1.833,1.5 1.833,1.25 false 5.417,1.552 5.417,1.302 false 0.104,0.094 0.417,0.333 0.313,0.24 12 false *A 3.521,0.083 3.833,0.333 0.313,0.25 12 false *B 1.76,1.49 2.073,1.646 0.313,0.156 10 false *a 5.344,1.531 5.656,1.688 0.313,0.156 10 false *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Scribed Line - -
V100145

Primer Application - -



d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new rear center ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work glove.



g.

Align the rear center ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the rear center ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds



B525253C01
1.917,1.521 1.917,1.271 true 5.167,1.542 5.167,1.292 true 0.083,0.094 0.396,0.333 0.313,0.24 12 false *A 3.417,0.094 3.75,0.333 0.333,0.24 12 false *B 1.823,1.51 2.073,1.677 0.25,0.167 10 true *a 5.083,1.5 5.333,1.667 0.25,0.167 10 true *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Scribed Line - -



Hide 89348R 3.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

NOTICE:
·

Installing the rear corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.



HINT:

Perform the following procedure only when replacement of a rear corner ultrasonic sensor retainer is necessary.


a.

Clean the rear bumper assembly surface.

i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Wipe off any tape adhesive residue with cleaner.



b.
B502899C03
1.51,0.156 1.823,0.354 0.313,0.198 10 false *a 2.635,1.167 2.948,1.365 0.313,0.198 10 false *a
*a 30 mm (1.18 in.)


Cover the sensor installation hole from the outside of the rear bumper cover with a 30 mm (1.18 in.) square piece of tape.


c.

Apply primer to the rear bumper assembly on the installation area of the rear corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear corner ultrasonic sensor retainer has been attached.



B525331C01
1.833,1.5 1.833,1.25 false 5.25,1.5 5.25,1.25 false 0.104,0.083 0.417,0.323 0.313,0.24 12 false *A 3.688,0.094 4,0.333 0.313,0.24 12 false *B 1.771,1.51 2.083,1.667 0.313,0.156 10 false *a 5.167,1.5 5.396,1.667 0.229,0.167 10 false *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Scribed Line - -
V100145

Primer Application - -



d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new rear corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work glove.



g.

Align the rear corner ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the rear corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds



i.

for LH Side:

B525330C01
1.833,1.5 1.833,1.25 true 5.25,1.5 5.25,1.25 true 0.083,0.083 0.396,0.333 0.313,0.25 12 false *A 3.417,0.094 3.729,0.333 0.313,0.24 12 false *B 5.167,1.5 5.396,1.667 0.229,0.167 10 true *a 1.771,1.5 2,1.667 0.229,0.167 10 true *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Scribed Line - -



ii.

for RH Side:

B525571C01
1.833,1.5 1.833,1.25 true 5.25,1.5 5.25,1.25 true 0.083,0.083 0.396,0.333 0.313,0.25 12 false *A 3.417,0.094 3.729,0.333 0.313,0.24 12 false *B 5.167,1.5 5.396,1.667 0.229,0.167 10 true *a 1.771,1.5 2,1.667 0.229,0.167 10 true *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Scribed Line - -




Hide 89342A 4.INSTALL REAR CENTER ULTRASONIC SENSOR

HINT:
·

Use the same procedure for the RH and LH side.

·

The following procedure is for the LH side.



a.

Attach the claw to install the rear center ultrasonic sensor.

NOTICE:
·

When reusing the sensor, make sure that each sensor is returned to its original position.

·

Check that the claw is securely fitted.

·
B494879C10
0,0 0,0 false
V100155

Microphone Surface


Do not push the microphone surface.



HINT:

w/ Parking Support Brake System:

Align the connector with the protrusion of the mark when connecting it.


B525251C01
4.833,1.052 4.833,0.885 false 0.104,0.094 0.417,0.333 0.313,0.24 12 false *A 3.667,0.083 3.979,0.333 0.313,0.25 12 false *B 4.75,1.073 5.063,1.271 0.313,0.198 10 false *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Protrusion of the mark - -
V113147

Install in this Direction - -



b.

Connect the connector.

B525247C01
0.083,0.094 0.396,0.333 0.313,0.24 12 false *A 3.583,0.083 3.917,0.333 0.333,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



Hide 89342 5.INSTALL REAR CORNER ULTRASONIC SENSOR

HINT:
·

Use the same procedure for the RH and LH side.

·

The following procedure is for the LH side.



a.

Attach the claw to install the rear corner ultrasonic sensor.

NOTICE:
·

When reusing the sensor, make sure that each sensor is returned to its original position.

·

Check that the claw is securely fitted.

·
B494879C10
0,0 0,0 false
V100155

Microphone Surface


Do not push the microphone surface.



HINT:

w/ Parking Support Brake System:

Align the connector with the protrusion of the mark when connecting it.


B525328C01
5.917,1.01 5.917,0.844 false 0.104,0.083 0.417,0.323 0.313,0.24 12 false *A 3.438,0.094 3.75,0.417 0.313,0.323 12 false *B 5.854,1 6.167,1.198 0.313,0.198 10 false *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Protrusion of the mark - -
V113147

Install in this Direction - -



b.

Connect the connector.

B525589C01
0.104,0.094 0.417,0.333 0.313,0.24 12 false *A 3.521,0.083 3.833,0.333 0.313,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



Hide 6.INSTALL REAR BUMPER ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Hands Free Power Back Door)


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 8.INSTALL BATTERY HOLE COVER (for HV Model, w/ Hands Free Power Back Door)

Hide 58416K 9.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model, w/ Hands Free Power Back Door)

Hide 58410B 10.INSTALL DECK BOARD ASSEMBLY (for HV Model, w/ Hands Free Power Back Door)

Hide 891B2 11.INSPECT KICK DOOR CONTROL SENSOR (w/ Hands Free Power Back Door)

Hide 12. INITIALIZE POWER BACK DOOR SYSTEM (w/ Hands Free Power Back Door)