Home › General › MAINTENANCE › P710 HYBRID TRANSAXLE FLUID › from 2019.09
RM3620E _V1 General _076298 MAINTENANCE _0378748 P710 HYBRID TRANSAXLE FLUID A

MAINTENANCE  P710 HYBRID TRANSAXLE FLUID  REPLACEMENT  


PROCEDURE

Hide 53896B 1.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53737D 5.REMOVE FRONT FENDER APRON SEAL LH

Hide 6.REPLACE HYBRID TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.
C377438

Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly. [#2]


c.
C377439

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly and drain the hybrid transaxle fluid. [#3]


d.

Using a 10 mm hexagon socket wrench, temporarily install the drain plug and gasket to the hybrid vehicle transaxle assembly. [#4]

HINT:

Reuse the old gasket as the drain plug will be removed again.



e.
C377440C01
2.385,1.094 2.5,0.823 2.5,0.823 2.635,0.823 false 2.698,0.74 2.938,0.948 0.24,0.208 10 false *a 3.146,1.708 3.375,1.917 0.229,0.208 10 false *b
*a Filler Nozzle
*b 0 to 10 mm (0 to 0.394 in.)


Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. [#5]

NOTICE:
·

Use Toyota Genuine ATF WS.

Using transmission fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.

·

Be sure to fully insert the filler nozzle into the filler plug opening.

·

Be sure to add hybrid transaxle fluid slowly. If hybrid transaxle fluid is added quickly, the hybrid transaxle fluid may hit internal parts and bounce back, resulting in hybrid transaxle fluid coming out of the filler plug opening.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

An insufficient or excessive amount of hybrid transaxle fluid may damage the hybrid vehicle transaxle assembly.




f.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly. [#6]

HINT:

Reuse the old gasket as the filler plug will be removed again.



g.

Lower the vehicle. [#7]


h.

Put the engine in Inspection Mode (Maintenance Mode). [#8]

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


i.

Idle the engine for 30 seconds with the power switch on (READY). [#9]


j.

Turn the power switch off. [#10]


k.

Repeat steps [#1] to [#10].


l.

Repeat steps [#1] to [#3].


m.

Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


n.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



Hide 9.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 53737D 10.INSTALL FRONT FENDER APRON SEAL LH

Hide 51420 11.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51441 12.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53895B 13.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

Hide 53896B 14.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH