Home › Drivetrain › Q610 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE FLUID › from 2019.09
RM3620E _52 Drivetrain _080124 Q610 HYBRID TRANSMISSION / TRANSAXLE _0388722 HYBRID TRANSAXLE FLUID G

Q610 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE FLUID  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

For the hybrid transaxle fluid, use Toyota Genuine ATF WS.

Using transmission fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.


PROCEDURE

Hide 58398F 1.REMOVE NO. 1 FLOOR UNDER COVER (w/ No. 1 Floor Under Cover)

Hide 2.INSPECT HYBRID TRANSAXLE FLUID

a.

Make sure that the vehicle will remain level, and lift the vehicle.


b.
C407249C01
2,3.177 2.292,3.177 2.292,3.177 2.479,2.948 false 2.74,3.063 3.042,3.063 false 1.802,3.094 2.021,3.323 0.219,0.229 10 false *1 3.073,2.979 3.302,3.219 0.229,0.24 10 false *2
*1 10 mm Union Nut Wrench
*2 10 mm Straight Hexagon


Using a 10 mm union nut wrench and 10 mm straight hexagon, remove the filler plug and gasket from the rear traction motor with transaxle assembly.


c.
C405622C01
0.26,0.896 0.427,0.896 0.427,0.896 0.896,1.26 true 0.052,0.813 0.271,1.073 0.219,0.26 10 false *1 3.042,1.635 3.281,1.896 0.24,0.26 10 false *a
*1 Filler Plug
*a 0 to 5 mm (0 to 0.196 in.)


Check that the hybrid transaxle fluid level is between 0 to 5 mm (0 to 0.196 in.) from the bottom lip of the filler plug opening. (If the hybrid transaxle fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

NOTICE:
·

Stop the vehicle on a level surface.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

An insufficient or excessive amount of hybrid transaxle fluid may damage the rear traction motor with transaxle assembly.

·

If the hybrid transaxle fluid was replaced or hybrid transaxle fluid was added, make sure to recheck the hybrid transaxle fluid level after driving the vehicle.




d.

Check for leaks if the hybrid transaxle fluid level is low. (If there are no hybrid transaxle fluid leaks but the amount of the hybrid transaxle fluid is insufficient, add hybrid transaxle fluid.)

Click here


e.
C407250C01
2.708,3.021 3.052,3.021 false 1.917,3.188 2.229,3.188 2.229,3.188 2.385,2.927 false 1.708,3.104 1.927,3.313 0.219,0.208 10 false *1 3.083,2.938 3.333,3.167 0.25,0.229 10 false *2 1.583,2.156 1.823,2.396 0.24,0.24 10 false *a
*1 10 mm Union Nut Wrench
*2 10 mm Straight Hexagon
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench and 10 mm straight hexagon, install the filler plug and a new gasket to the rear traction motor with transaxle assembly.

Torque:
Specified tightening torque : 39 N*m (398 kgf*cm, 29 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 34.8 N*m (355 kgf*cm, 26 ft.*lbf)




Hide 3.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 58398F 4.INSTALL NO. 1 FLOOR UNDER COVER (w/ No. 1 Floor Under Cover)