Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for HV Model 4WD/AWD) › 2019.02–2020.05
RM3620E _53 Suspension _076491 REAR SUSPENSION _0389149 REAR SUSPENSION MEMBER(for HV Model 4WD/AWD) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for HV Model 4WD/AWD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Rear wheel alignment adjustment
·

Clear zero point calibration data.

·

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for HV model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FXS w/ Canister Pump Module:

(Click here)

·

for A25A-FXS w/o Canister Pump Module:

(Click here)

·

for A25B-FXS:

(Click here)



CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 58398F 1.REMOVE NO. 1 FLOOR UNDER COVER (w/ NO. 1 FLOOR UNDER COVER)

a.
C413725

Remove the 3 bolts, 3 clips and No. 1 floor under cover from the rear suspension member sub-assembly.


Hide 48812 2.REMOVE REAR STABILIZER BAR

Hide 3.REMOVE REAR DRIVE SHAFT ASSEMBLY LH

Hide 4.REMOVE REAR DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 5.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 6.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 7.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C410956

Remove the bolt, nut and rear No. 1 suspension arm assembly from the rear suspension member sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48710A 8.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 10.REMOVE NO. 2 INVERTER PROTECTOR (w/ NO. 2 INVERTER PROTECTOR)

Hide 82111 11.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 82111 15.CONNECT ENGINE ROOM MAIN WIRE

Hide 16.INSTALL NO. 2 INVERTER PROTECTOR (w/ NO. 2 INVERTER PROTECTOR)

Hide 17.REMOVE REAR SEAT ASSEMBLY

Hide 73706 18.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH

Hide 64910N 19.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 58410B 20.REMOVE DECK BOARD ASSEMBLY

Hide 58417H 21.REMOVE REAR NO. 3 FLOOR BOARD

Hide 64993 22.REMOVE REAR DECK FLOOR BOX (w/o Spare Tire)

Hide 58386 23.REMOVE REAR FLOOR FINISH PLATE

Hide 58577E 24.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE

Hide 67918E 25.REMOVE REAR DOOR SCUFF PLATE LH

Hide 62332C 26.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62552F 27.REMOVE REAR SEAT SIDE GARNISH LH

Hide 73708A 28.REMOVE TETHER ANCHOR BRACKET SET

Hide 58460D 29.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

Hide 64740E 30.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 821H1 31.DISCONNECT HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A435162

Disengage the clamp.


b.
A445300C01
2.594,3.104 2.208,3.104 2.208,3.104 1.896,2.667 true 2.646,3 2.958,3.198 0.313,0.198 10 false *a
*a Waterproof Seal


Remove the 2 bolts and HV floor under wire from the rear traction motor with transaxle assembly.

NOTICE:
·

Do not damage the terminals, interlock connector or rear traction motor with transaxle assembly during disconnection.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not allow any foreign matter or water to enter the rear traction motor with transaxle assembly.

·

Although the connector may feel loose, this is not due to a malfunction.




c.

Temporarily install the HV floor under wire as shown in the illustration.

C410662C01
0,0 0,0 false
V100135

Front of the Vehicle - -



Hide 51206A 32.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C410656

Disconnect the 2 connectors.


b.

Remove the grommet of the wire harness and pass the connector through the hole to the outside of the vehicle.


c.

Disengage the 5 clamps to separate the wire harness.

C410658


d.
C410660C01
2.75,4.146 2.75,3.979 2.75,3.979 2.917,3.979 false 2.021,4.115 2.021,3.948 2.021,3.948 2.188,3.948 false 0.958,4.125 0.875,3.958 0.875,3.958 1.458,4.042 true 0.396,4.25 0.396,4.083 0.396,4.083 0.563,4.083 false 0.604,4.021 0.938,4.271 0.333,0.25 10 false *a 2.958,3.917 3.208,4.167 0.25,0.25 10 false *b 2.229,3.885 2.479,4.135 0.25,0.25 10 false *b 0.719,3.865 0.969,4.115 0.25,0.25 10 false *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
C410424

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.



e.

Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH.


f.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



g.

Remove the 4 rear suspension member cushions from the rear suspension member sub-assembly.

HINT:

Make sure to place an identification mark on the rear suspension member cushion so that they can be reinstalled to their original positions.



Hide G1050 34.REMOVE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

Hide 48790 35.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 36.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52272A 37.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

Hide 52271E 38.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 52276B 39.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

Hide 52275C 40.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

HINT:

Perform the same procedure as for the LH side.


Hide 41651G 41.REMOVE DIFFERENTIAL MOUNT CUSHION

a.

Using SST, remove the differential mount cushion.

SST
09316-12010  
09570-24011  

C423345C01
5.688,2.521 5.854,2.854 5.854,2.854 6.021,2.854 false 5.417,1.448 5.417,1.167 5.417,1.167 6.333,1.167 false 6.063,1.583 6.063,1.167 false 6.146,1.563 6.146,1.167 false 6.063,2.802 6.396,3.052 0.333,0.25 10 false *1 3.469,1.375 3.802,1.625 0.333,0.25 10 false *a 2.208,1.365 2.625,1.615 0.417,0.25 10 false *b 6.375,1.104 6.875,1.438 0.5,0.333 10 false SST
*1 Rear Suspension Member Sub-assembly - -
*a Turn *b Hold
V100135

Turning Direction
V100136

Front of Vehicle
V100137

SST Bolt Position - -


NOTICE:
·

Do not bring SST into contact with the rear suspension member sub-assembly.

·

Before using SST, apply grease to SST bolt.

·

Set SST in the correct direction.

·

Do not tilt the bolt of SST.

·

Do not reuse the differential mount cushion.




Hide 42.REMOVE HOLE PLUG

a.
C410661N01
1.063,0.427 1.219,0.625 0.156,0.198 10 false A 1.906,0.146 2.063,0.344 0.156,0.198 10 false A 2.333,0.833 2.49,1.031 0.156,0.198 10 false A 3.25,0.906 3.406,1.104 0.156,0.198 10 false A 0.667,1.458 0.823,1.656 0.156,0.198 10 false B 0.26,1.063 0.417,1.26 0.156,0.198 10 false B

Remove the 6 hole plugs from the rear suspension member sub-assembly.

HINT:

There are 2 different shapes of hole plug.