Home › General › MAINTENANCE › UB80F AUTOMATIC TRANSAXLE FLUID › from 2019.09
RM3620E _V1 General _076298 MAINTENANCE _0378721 UB80F AUTOMATIC TRANSAXLE FLUID A

MAINTENANCE  UB80F AUTOMATIC TRANSAXLE FLUID  REPLACEMENT  


PROCEDURE

Hide 53896B 1.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53737D 5.REMOVE FRONT FENDER APRON SEAL LH

Hide 6.REPLACE AUTOMATIC TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).



b.
C402638

Remove the refill plug and gasket from the automatic transaxle case sub-assembly. [#2]


c.
C402774

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing. [#3]


d.
C402778C01
2.75,0.917 2.854,0.917 false 2.552,0.833 2.719,1 0.167,0.167 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid. [#4]


e.
C402773

Measure the amount of automatic transaxle fluid drained. [#5]

HINT:

Add the same amount of automatic transaxle fluid in step [#8].



f.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing. [#6]

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


g.
C402774

Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing. [#7]

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



h.
C402649

Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8]

NOTICE:

Use Toyota Genuine ATF WS.

Using transmission fluid other than the above type may cause abnormal noise or vibration, or damage the transmission of your vehicle.



i.
C402638

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9]

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



j.

Lower the vehicle. [#10]


k.

Start the engine. [#11]


l.

Slowly move the shift lever from P to D, and then back to P. [#12]

HINT:
·

Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.

·

Keep the shift lever in each position for approximately 3 seconds.




m.

Allow the engine to idle for 30 seconds to warm it up. [#13]


n.

Turn the ignition switch off. [#14]


o.

Repeat steps [#1] to [#14].


p.

Repeat steps [#1] to [#10].


Hide 7.ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID

Hide 8.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the GTS)

Hide 9.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the GTS)

Hide 53737D 12.INSTALL FRONT FENDER APRON SEAL LH

Hide 51420 13.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51441 14.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53895B 15.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

Hide 53896B 16.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH