Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2019.09–2020.08
RM3620E _51 Engine / Hybrid System _076317 A25A-FKS ENGINE MECHANICAL _0371512 ENGINE ASSEMBLY A

A25A-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for UB80E:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
for UB80F:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:
(Click here)
w/o Canister Pump Module:
(Click here)
Replacement of automatic transaxle assembly
for UB80E:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
for UB80F:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UB60E:
(Click here)
for UB60F:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
1.

Perform reset memory

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.SECURE STEERING WHEEL ASSEMBLY

Hide 7.REMOVE FRONT WHEELS

Hide 53896B 8.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

a.
A434180

for Short Type:

i.

Remove the 3 screws.


ii.

Detach the clip and remove the front fender front splash shield LH.



b.
A434222

for Long Type:

i.

Remove the 4 screws.


ii.

Detach the clip and remove the front fender front splash shield LH.



Hide 53895B 9.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

a.
A434181

for Short Type:

i.

Remove the 3 screws.


ii.

Detach the clip and remove the front fender front splash shield RH.



b.
A434223

for Long Type:

i.

Remove the 4 screws.


ii.

Detach the clip and remove the front fender front splash shield RH.



Hide 51441 10.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the 2 bolts and 10 screws. (Short Type Front Fender Front Splash Shield)


b.

Remove the 2 bolts and 8 screws. (Long Type Front Fender Front Splash Shield)


c.

Detach the guide and remove the No. 1 engine under cover.

A434182C01
1.75,2.365 1.948,2.542 0.198,0.177 10 true *a 5,2.24 5.198,2.417 0.198,0.177 10 true *a
*a Short Type Front Fender Front Splash Shield - -
V100135

Bolt
V100136

Screw



Hide 51420 11.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

a.
A429096C01
0.042,0.031 0.281,0.25 0.24,0.219 10 false *a 0.052,2.385 0.281,2.604 0.229,0.219 10 false *b
*a w/o Air Duct
*b w/ Air Duct
V100135

Bolt
V100136

Screw


Remove the 2 bolts, 2 screws, 6 clips and No. 2 engine under cover assembly.


Hide 53737D 12.REMOVE FRONT FENDER APRON SEAL LH

a.
A434185C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Remove the 2 bolts, clip and front fender apron seal LH.


Hide 53736E 13.REMOVE FRONT FENDER APRON SEAL RH

A434186C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


a.

Remove the 2 bolts, clip and front fender apron seal RH.


Hide 52618 15.REMOVE FRONT LOWER BUMPER ABSORBER

a.
A431799

Remove the 5 bolts.


b.

Detach the 2 claws and remove the front lower bumper absorber.


Hide 16.DRAIN ENGINE COOLANT

Hide 19.DRAIN TRANSFER OIL (for 4WD/AWD)

Hide 12601B 20.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A429097C01
0.031,0.031 0.271,0.292 0.24,0.26 10 false *A 0.042,2.479 0.281,2.719 0.24,0.24 10 false *B
*A for LHD
*B for RHD


Lift the front of the No. 1 engine cover sub-assembly to detach the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to detach the clip and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to detach both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide 17750A 21.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 22.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 24.REMOVE BATTERY

Hide 74404B 25.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A429098

Detach the 2 clamps from the battery clamp sub-assembly.


b.
A429099C01
0.844,0.854 1.021,0.854 1.021,0.854 1.229,1.271 true 2.156,1.146 2.5,0.792 2.5,0.792 2.667,0.792 true 1.104,0.177 1.281,0.177 1.281,0.177 1.542,0.365 true 0.635,0.75 0.833,0.948 0.198,0.198 10 true *1 2.708,0.688 2.906,0.885 0.198,0.198 10 true *2 0.906,0.073 1.104,0.271 0.198,0.198 10 true *3
*1 No. 2 Engine Wire
*2 Engine Room Main Wire
*3 Positive (+) Battery Terminal


Detach the 2 clamps and disconnect the engine room main wire and No. 2 engine wire from the battery clamp sub-assembly.


c.

Remove the nut and disconnect the engine room main wire and No. 2 engine wire from the positive (+) battery terminal.


d.

Detach the 2 claws and disconnect the engine room main wire from the No. 2 engine wire.


e.
A429100

Remove the 3 bolts and battery clamp sub-assembly.


Hide 82123 26.DISCONNECT NO. 3 ENGINE WIRE

a.
A429101

Detach the clamp from the bracket.


b.

Remove the bolt and disconnect the No. 3 engine wire from the automatic transaxle assembly.


Hide 33820B 27.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C402660C01
2.083,2.167 1.917,2.167 1.917,2.167 1.74,2.344 false 2.125,2.083 2.292,2.25 0.167,0.167 10 false *a 3,3.271 3.167,3.438 0.167,0.167 10 false *b
*a Clip
*b 45° to 60°


While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


b.
C402740

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 23826 28.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A429102

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the Purge VSV.


Hide 44773F 29.DISCONNECT UNION TO CHECK VALVE HOSE

a.
A429103

Slide the clip and disconnect the union to check valve hose from the vacuum pump assembly.


Hide 44777 30.DISCONNECT NO. 1 VACUUM HOSE CONNECTOR

Hide 87245 31.DISCONNECT INLET HEATER WATER HOSE

a.
A429104C01
1.26,1.813 1.427,1.813 1.427,1.813 1.583,1.49 true 1.052,1.698 1.271,1.917 0.219,0.219 10 true *a
*a Retainer
V113147

Pull out
V113148

Pull off


Pull out the retainer to detach the lock claws and pull off the inlet heater water hose.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater water hose connector with plastic bags to prevent damage and contamination.


Hide 87246 32.DISCONNECT OUTLET HEATER WATER HOSE

a.
A429106C01
1.729,1.406 1.938,1.625 1.938,1.625 2.125,1.625 true 2.167,1.5 2.396,1.729 0.229,0.229 10 true *a
*a Retainer
V113147

Pull out
V113148

Pull off


Pull out the retainer to detach the lock claws and pull off the outlet heater water hose.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector with plastic bags to prevent damage and contamination.


Hide 23901 33.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A429108

Remove the No. 1 fuel pipe clamp from the fuel tube connector.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Disconnect the fuel tube sub-assembly.

i.
A429109

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 16571C 34.DISCONNECT NO. 1 RADIATOR HOSE

a.
A429110

Detach the clamp to disconnect the No. 1 radiator hose from the No. 1 radiator bracket.


b.

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 35.DISCONNECT NO. 2 RADIATOR HOSE

a.
A429111

Detach the clamp and disconnect the No. 2 radiator hose from the fan with motor assembly.


b.

Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.


Hide 88704 36.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 37.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 38.DISCONNECT WIRE HARNESS

HINT:

After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.


a.
A429114

Detach the 3 claws and remove the No. 2 relay block cover.


b.
A429115

Remove the nut from the engine room relay block and junction block assembly.


c.

Disconnect the 5 connectors from the engine room relay block and junction block assembly.


d.

Using a screwdriver, detach the claw and disconnect the wire harness from the engine room relay block and junction block assembly.


e.
A429116

Detach the clamp.


f.

Remove the bolt and disconnect the wire harness from the vehicle body.


Hide 16282 39.REMOVE NO. 5 WATER BY-PASS HOSE

a.
A429117

Slide the 2 clips and remove the No. 5 water by-pass hose from the radiator assembly and No. 3 water by-pass pipe.


Hide 58166A 40.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58399D 41.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 58165C 42.REMOVE FRONT FLOOR COVER RH (w/ Cover)

Hide 58398F 43.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 17410 44.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58152A 45.REMOVE LOWER NO. 1 FRONT FLOOR HEAT INSULATOR (for 4WD/AWD)

Hide 37110 46.REMOVE PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)

Hide 43502H 47.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 48.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 49.DISCONNECT FRONT SPEED SENSOR LH

Hide 50.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 51.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 52.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 53.DISCONNECT TIE ROD ASSEMBLY LH

Hide 45460 54.DISCONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 55.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 56.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45220 60.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 61.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

A457672C01
0,0 0,0 false
V113146

Attachments - -


NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.




b.
A429118

Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A429119C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.


d.
A429120C03
2.104,4.344 2.417,4.344 true 1.927,1.688 2.073,1.688 2.073,1.688 2.24,1.333 true 1.052,4.323 1.365,4.323 true 1.448,1.677 1.313,1.677 1.313,1.677 1.156,1.417 true 1.042,1.042 1.188,1.24 0.146,0.198 10 true B 0.25,2.75 0.396,2.948 0.146,0.198 10 true A 0.417,4.104 0.563,4.302 0.146,0.198 10 true D 0.594,3.75 0.74,3.948 0.146,0.198 10 true C 2.26,1.021 2.406,1.219 0.146,0.198 10 true B 3.042,2.729 3.188,2.927 0.146,0.198 10 true A 0.417,4.438 0.563,4.635 0.146,0.198 10 true D 2.885,4.438 3.031,4.635 0.146,0.198 10 true D 2.906,4.094 3.052,4.292 0.146,0.198 10 true D 2.708,3.76 2.854,3.958 0.146,0.198 10 true C 1.75,1.594 1.948,1.781 0.198,0.188 10 true *1 1.479,1.594 1.677,1.802 0.198,0.208 10 true *2 1.906,4.24 2.094,4.438 0.188,0.198 10 true *3 1.385,4.24 1.573,4.438 0.188,0.198 10 true *4
*1 Front Bumper Extension Sub-assembly LH
*2 Front Bumper Extension Sub-assembly RH
*3 Rear Front Suspension Member Brace LH
*4 Rear Front Suspension Member Brace RH
V100135

Bolt
V100136

Nut


Remove the 2 bolts (A), 2 bolts (B), 4 nuts and front bumper extension sub-assembly LH and front bumper extension sub-assembly RH from the front frame assembly and vehicle body.


e.

Remove the 2 bolts (C), 4 bolts (D) and rear front suspension member brace LH and rear front suspension member brace RH from the front frame assembly and vehicle body.


f.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 23825 62.REMOVE FUEL DELIVERY GUARD

a.
A429121

Remove the bolt and fuel delivery guard from the engine mounting bracket RH.


Hide 63.INSTALL ENGINE HANGERS

a.
A429122C01
0.875,0.583 1.094,0.365 1.094,0.365 1.26,0.365 true 2.708,0.604 2.844,0.365 2.844,0.365 3.01,0.365 true 1.281,0.26 1.5,0.469 0.219,0.208 10 true *1 3.063,0.271 3.302,0.479 0.24,0.208 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 11361J 64.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A429123

Remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 32101A 65.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 16261G 67.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 45319 70.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 17650H 74.REMOVE VACUUM SWITCHING VALVE (for Active Control Engine Mount System)

Hide 12361 75.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.



Hide 12371A 77.REMOVE REAR ENGINE MOUNTING INSULATOR (for 2WD)

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACTIVE CONTROL ENGINE MOUNT (for Rear Side)>REMOVAL

Hide 37117 78.REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD/AWD)

Hide 12371A 79.REMOVE REAR ENGINE MOUNTING INSULATOR (for 4WD/AWD)

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL

Hide 32101 84.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 19315 85.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 82121 86.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 87.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 88.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


Hide 12305 89.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A429127C01
1.74,0.927 1.896,0.542 1.896,0.542 2.083,0.542 true 2.021,1.781 2.021,1.344 true 1.958,1.813 2.167,2.021 0.208,0.208 10 true *1 2.104,0.448 2.302,0.656 0.198,0.208 10 true *2
*1 Suction Pipe Sub-assembly
*2 Air Conditioning Tube And Accessory Assembly


Disconnect the connector.


b.

Detach the 2 clamps and disconnect the suction pipe sub-assembly and air conditioning tube and accessory assembly.


c.
A429128

Disconnect the No. 6 water by-pass hose.


d.

Detach the clamp.


e.
A429129

Remove the bolt, nut and the radiator reserve tank assembly.


f.

Detach the 2 clamps and disconnect the wire harness from the radiator reserve tank assembly.


g.
A429130

Remove the bolt and disconnect the No. 2 ground wire from the engine mounting insulator sub-assembly RH.


h.
A429131

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH.


Hide 12341 90.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A429132

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12372A 91.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



Hide 12304 92.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

a.
A429133

Remove the 4 bolts and engine mounting bracket sub-assembly LH from the vehicle body.