Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2019.09
RM3620E _51 Engine / Hybrid System _076317 A25A-FKS ENGINE MECHANICAL _0371512 ENGINE ASSEMBLY A

A25A-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 12304 1.INSTALL ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

a.
A429133N01
2.448,1.625 2.604,1.823 0.156,0.198 10 true B 2.021,0.302 2.177,0.5 0.156,0.198 10 true A 0.875,1.625 1.031,1.823 0.156,0.198 10 true C 1.115,0.26 1.271,0.458 0.156,0.198 10 true D

Install the engine mounting bracket sub-assembly LH to the vehicle body with the 4 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 4 bolts in the order of (B), (C), (D) and (A).



Hide 12372A 2.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



Hide 12341 3.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A429132N01
0.938,1.729 1.094,1.927 0.156,0.198 10 true A 2.542,1.26 2.698,1.458 0.156,0.198 10 true B

Install the engine mounting spacer to the vehicle body with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts in the order of (B) and (A).



Hide 12305 4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A429131N01
0.625,1.396 0.781,1.594 0.156,0.198 10 true A 2.688,1.615 2.844,1.813 0.156,0.198 10 true B 2.448,0.542 2.604,0.74 0.156,0.198 10 true C

Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.

Connect the No. 2 ground wire to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A429129N02
3.177,1.24 3.333,1.438 0.156,0.198 10 true 2 2.99,3.115 3.146,3.313 0.156,0.198 10 true 1

Install the radiator reserve tank assembly with the bolt and nut in the order shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Attach the 2 clamps and connect the wire harness to the radiator reserve tank assembly.


e.
A429128

Attach the clamp.


f.

Connect the No. 6 water by-pass hose.


g.
A429127C01
1.74,0.927 1.896,0.542 1.896,0.542 2.083,0.542 true 2.021,1.781 2.021,1.344 true 1.958,1.813 2.167,2.021 0.208,0.208 10 true *1 2.104,0.448 2.302,0.656 0.198,0.208 10 true *2
*1 Suction Pipe Sub-assembly
*2 Air Conditioning Tube And Accessory Assembly


Attach the 2 clamps to connect the suction pipe sub-assembly and air conditioning tube and accessory assembly.


h.

Connect the connector.


Hide 6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 82121 7.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 19315 8.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 32101 9.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 12371A 14.INSTALL REAR ENGINE MOUNTING INSULATOR (for 4WD/AWD)

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>INSTALLATION

Hide 37117 15.INSTALL PROPELLER SHAFT HEAT INSULATOR (for 4WD/AWD)

Hide 12371A 16.INSTALL REAR ENGINE MOUNTING INSULATOR (for 2WD)

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACTIVE CONTROL ENGINE MOUNT (for Rear Side)>INSTALLATION

Hide 12361 18.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.



Hide 17650H 19.INSTALL VACUUM SWITCHING VALVE (for Active Control Engine Mount System)

Hide 45319 23.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 16261G 26.INSTALL FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 11361J 29.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 30.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


Hide 23825 31.INSTALL FUEL DELIVERY GUARD

a.

Install the fuel delivery guard to the engine mounting bracket RH with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 32.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

Perform inspection after repair after replacing the engine assembly.



a.

Set the engine assembly with transaxle on an engine lifter.

A457672C01
0,0 0,0 false
V113146

Attachments - -


NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.
A429120C03
2.104,4.344 2.417,4.344 true 1.927,1.688 2.073,1.688 2.073,1.688 2.24,1.333 true 1.052,4.323 1.365,4.323 true 1.448,1.677 1.313,1.677 1.313,1.677 1.156,1.417 true 1.042,1.042 1.188,1.24 0.146,0.198 10 true B 0.25,2.75 0.396,2.948 0.146,0.198 10 true A 0.417,4.104 0.563,4.302 0.146,0.198 10 true D 0.594,3.75 0.74,3.948 0.146,0.198 10 true C 2.26,1.021 2.406,1.219 0.146,0.198 10 true B 3.042,2.729 3.188,2.927 0.146,0.198 10 true A 0.417,4.438 0.563,4.635 0.146,0.198 10 true D 2.885,4.438 3.031,4.635 0.146,0.198 10 true D 2.906,4.094 3.052,4.292 0.146,0.198 10 true D 2.708,3.76 2.854,3.958 0.146,0.198 10 true C 1.75,1.594 1.948,1.781 0.198,0.188 10 true *1 1.479,1.594 1.677,1.802 0.198,0.208 10 true *2 1.906,4.24 2.094,4.438 0.188,0.198 10 true *3 1.385,4.24 1.573,4.438 0.188,0.198 10 true *4
*1 Front Bumper Extension Sub-assembly LH
*2 Front Bumper Extension Sub-assembly RH
*3 Rear Front Suspension Member Brace LH
*4 Rear Front Suspension Member Brace RH
V100135

Bolt
V100136

Nut


Install the front bumper extension sub-assembly LH and front bumper extension sub-assembly RH to the front frame assembly and vehicle body with the 2 bolts (A), 2 bolts (B) and 4 nuts.

Torque:
Bolt (A) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Bolt (B) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Nut : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


d.

Install the rear front suspension member brace LH and rear front suspension member brace RH to the front frame assembly and vehicle body with the 2 bolts (C) and 4 bolts (D).

Torque:
Bolt (C) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Bolt (D) : 60 N*m (612 kgf*cm, 44 ft.*lbf)


e.

Install the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



f.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 45220 33.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 48069 37.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 38.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 39.CONNECT TIE ROD ASSEMBLY LH

Hide 45460 40.CONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 41.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 42.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43.CONNECT FRONT SPEED SENSOR LH

Hide 44.CONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 45.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 46.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 47.STAKE FRONT AXLE SHAFT NUT LH

Hide 43501H 48.STAKE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 37110 49.TEMPORARILY INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)

Hide 37110 50.TIGHTEN PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)

Hide 51.INSPECT AND ADJUST JOINT ANGLE (for 4WD/AWD)

Hide 58152A 52.INSTALL LOWER NO. 1 FRONT FLOOR HEAT INSULATOR (for 4WD/AWD)

Hide 17410 53.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 58398F 54.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 58165C 55.INSTALL FRONT FLOOR COVER RH (w/ Cover)

Hide 58399D 56.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 58166A 57.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 16282 58.INSTALL NO. 5 WATER BY-PASS HOSE

a.

Install the No. 5 water by-pass hose to the radiator assembly and No. 3 water by-pass pipe, and slide the 2 clips to secure it.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 5 water by-pass hose is securely inserted to the stopper.



A436615C01
3.656,0.323 3.781,0.323 3.781,0.323 3.948,0.667 true 6.813,0.531 6.667,0.531 6.667,0.531 6.25,0.99 true 3.125,0.125 3.406,0.333 0.281,0.208 10 false *a 4.5,0.458 4.688,0.646 0.188,0.188 10 false *c 6.604,1.396 6.802,1.573 0.198,0.177 10 false *d 3.469,0.229 3.646,0.417 0.177,0.188 10 false *e 3.906,0.094 4.073,0.292 0.167,0.198 10 false *f 4.76,0.906 4.969,1.135 0.208,0.229 10 false *g 6.833,0.917 7.031,1.115 0.198,0.198 10 false *h 3.792,2.49 3.969,2.677 0.177,0.188 10 false *i 2.229,1.573 2.385,1.771 0.156,0.198 10 true A 0.656,1.344 0.813,1.542 0.156,0.198 10 true B 5.24,0.104 5.438,0.302 0.198,0.198 10 false *b 6.833,0.438 7.01,0.625 0.177,0.188 10 false *e 5.854,0.094 6.021,0.292 0.167,0.198 10 false *f 5.708,2.49 5.885,2.677 0.177,0.188 10 false *j
*a View A *b View B
*c 360° *d 120°
*e Paint Mark *f Upper Side
*g Front Side *h Rear Side
*i 2 to 7 mm (0.0787 to 0.276 in.) *j 2 to 5 mm (0.0787 to 0.197 in.)



Hide 59.CONNECT WIRE HARNESS

a.
A429116

Connect the wire harness to the vehicle body with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Attach the clamp.


c.
A429115

Attach the claw to install the wire harness to the engine room relay block and junction block assembly.


d.

Connect the 5 connectors to the engine room relay block and junction block assembly.


e.

Install the nut to the engine room relay block and junction block assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.
A429114

Attach the 3 claws and install the No. 2 relay block cover.


Hide 88711 60.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 61.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 16572D 62.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 2 radiator hose is securely inserted to the stopper.



A436614C01
4.99,1.927 4.99,1.729 4.99,1.729 4.375,1.51 true 3.344,0.667 3.542,0.865 0.198,0.198 10 false *a 4.719,1 4.917,1.198 0.198,0.198 10 false *b 4.927,1.958 5.125,2.156 0.198,0.198 10 false *c 3.958,0.573 4.146,0.771 0.188,0.198 10 false *d 5.01,1.406 5.208,1.604 0.198,0.198 10 false *e 5.5,2.073 5.677,2.25 0.177,0.177 10 false *f 1.5,1.896 1.656,2.094 0.156,0.198 10 true A
*a View A *b 120°
*c Paint Mark *d Upper Side
*e RH Side *f 2 to 5 mm (0.0787 to 0.197 in.)



b.

Connect the No. 2 radiator hose to the fan with motor assembly with the clamp.


Hide 16571C 63.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 1 radiator hose is securely inserted to the stopper.



A436613C01
3.656,0.802 3.969,0.802 3.969,0.802 4.115,1.25 true 3.281,0.417 3.479,0.635 0.198,0.219 10 false *a 4.344,0.708 4.563,0.896 0.219,0.188 10 false *b 3.458,0.698 3.646,0.896 0.188,0.198 10 false *c 4.052,0.469 4.25,0.677 0.198,0.208 10 false *d 3.219,1.479 3.417,1.688 0.198,0.208 10 false *e 5.51,2.063 5.698,2.26 0.188,0.198 10 false *f 2.031,1.49 2.188,1.688 0.156,0.198 10 true A
*a View A *b 90°
*c Paint Mark *d Upper Side
*e Front Side *f 2 to 7 mm (0.0787 to 0.276 in.)



b.

Connect the No. 1 radiator hose to the No. 1 radiator bracket with the clamp.


Hide 23901 64.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly.

i.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



b.

Install the No. 1 fuel pipe clamp to the fuel tube connector.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 87246 65.CONNECT OUTLET HEATER WATER HOSE

a.
A403463C02
1.052,1.156 1.573,1.156 false 0.99,0.365 1.219,0.365 1.219,0.365 1.521,0.792 false 0.875,1.063 1.188,1.219 0.313,0.156 10 false *a 0.823,0.281 1.135,0.438 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater hose connector and securely insert the outlet heater water hose connector to the stopper of the pipe.


b.
A429107C01
1.75,1.417 1.99,1.719 1.99,1.719 2.167,1.719 true 2.198,1.615 2.427,1.833 0.229,0.219 10 true *a
*a Retainer
V113147

Push
V113148

Push in


Push in the retainer.


c.

Check that the No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector are securely connected by pulling on them.


Hide 87245 66.CONNECT INLET HEATER WATER HOSE

a.
A403462C02
1.01,0.979 1.438,0.979 false 1.875,0.969 2.302,0.969 false 1.021,1.354 1.448,1.354 false 1.844,1.365 2.281,1.917 2.281,1.917 2.594,1.917 false 0.813,0.885 1.125,1.042 0.313,0.156 10 false *a 0.833,1.271 1.146,1.427 0.313,0.156 10 false *b 2.365,0.896 2.677,1.052 0.313,0.156 10 false *a 2.635,1.844 2.948,2 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusions of the inlet heater water hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and securely insert the inlet heater water hose connector to the stopper of the pipe.


b.
A429105C01
1.323,1.729 1.479,1.729 1.479,1.729 1.573,1.458 true 1.094,1.625 1.302,1.854 0.208,0.229 10 true *a
*a Retainer
V113147

Push
V113148

Push in


Push in the retainer.


c.

Check that the flow shutting valve (water by-pass hose assembly) and inlet heater water hose connector are securely connected by pulling on them.


Hide 44777 67.CONNECT NO. 1 VACUUM HOSE CONNECTOR

Hide 44773F 68.CONNECT UNION TO CHECK VALVE HOSE

a.

Connect the union to check valve hose to the vacuum pump assembly and slide the clip to secure it.


Hide 23826 69.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the purge VSV and slide the clip to secure it.


Hide 33820B 70.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C402740

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


b.
C402666C01
0.583,2 0.75,2.167 0.167,0.167 10 false *a 2.25,2 2.417,2.167 0.167,0.167 10 false *b
*a Correct
*b Incorrect


Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.



Hide 82123 71.CONNECT NO. 3 ENGINE WIRE

a.
A429101

Connect the No. 3 engine wire to the automatic transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Attach the clamp to the bracket.


Hide 74404B 72.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.
A429100

Install the battery clamp sub-assembly with the 3 bolts.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


b.
A429134C01
1.365,0.76 1.479,0.469 1.479,0.469 1.667,0.469 false 1.063,1.01 0.833,0.76 0.833,0.76 0.656,0.76 false 0.76,1.656 0.677,1.396 0.677,1.396 0.5,1.396 false 1.708,0.375 1.927,0.573 0.219,0.198 10 false *1 0.458,0.667 0.656,0.865 0.198,0.198 10 false *2 0.302,1.292 0.49,1.479 0.188,0.188 10 false *3
*1 Engine Room Main Wire
*2 No. 2 Engine Wire
*3 Positive (+) Battery Terminal


Attach the 2 claws and connect the engine room main wire to the No. 2 engine wire.


c.

Connect the engine room main wire and No. 2 engine wire to the positive (+) battery terminal with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Attach the 2 clamps and connect the engine room main wire and No. 2 engine wire to the battery clamp sub-assembly.


e.
A429098

Attach the 2 clamps to the battery clamp sub-assembly.


Hide 75.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 17750A 76.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 12601B 77.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A429097C01
0.031,0.031 0.271,0.292 0.24,0.26 10 false *A 0.042,2.479 0.281,2.719 0.24,0.24 10 false *B
*A for LHD
*B for RHD


Attach the 3 clips to install the No. 1 engine cover sub-assembly.

NOTICE:
·

Securely attach the clips.

·

If the clips are forcibly attached or struck with an object, they may be damaged.




Hide 78.INSPECT VACUUM HOSES

a.

Check that the vacuum hose is installed as shown in the illustration.

A429166C01
0.063,0.042 0.313,0.281 0.25,0.24 10 false *A 3.927,0.052 4.177,0.292 0.25,0.24 10 false *B
*A for 2WD *B for 4WD/AWD



Hide 79.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 82.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 85.ADD TRANSFER OIL (for 4WD/AWD)

Hide 86.ADD ENGINE COOLANT

Hide 89.INSPECT FOR ENGINE OIL LEAK

Hide 95.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 52618 96.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Attach the 2 claws to install the front lower bumper absorber.


b.

Install the 5 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53737D 98.INSTALL FRONT FENDER APRON SEAL LH

a.
A434185C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Install the front fender apron seal LH with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53736E 99.INSTALL FRONT FENDER APRON SEAL RH

a.
A434186C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Install the front fender apron seal RH with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51420 100.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

a.
A429096C01
0.042,0.031 0.281,0.25 0.24,0.219 10 false *a 0.052,2.385 0.281,2.604 0.229,0.219 10 false *b
*a w/o Air Duct
*b w/ Air Duct
V100135

Bolt
V100136

Screw


Install the No. 2 engine under cover assembly with the 2 bolts, 2 screws and 6 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 101.INSTALL NO. 1 ENGINE UNDER COVER

a.

Attach the guide and install the No. 1 engine under cover.


b.

Install the 2 bolts and 10 screws. (Short Type Front Fender Front Splash Shield)

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Install the 2 bolts and 8 screws. (Long Type Front Fender Front Splash Shield)

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)

A434182C01
1.75,2.365 1.948,2.542 0.198,0.177 10 true *a 5,2.24 5.198,2.417 0.198,0.177 10 true *a
*a Short Type Front Fender Front Splash Shield - -
V100135

Bolt
V100136

Screw



Hide 53896B 102.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

a.

for Short Type:

i.
A434180

Attach the clip to install the front fender front splash shield LH.


ii.

Install the 3 screws.



b.

for Long Type:

i.
A434222

Attach the clip to install the front fender front splash shield LH.


ii.

Install the 4 screws.



Hide 53895B 103.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

a.

for Short Type:

i.
A434181

Attach the clip to install the front fender front splash shield RH.


ii.

Install the 3 screws.



b.

for Long Type:

i.
A434223

Attach the clip to install the front fender front splash shield RH.


ii.

Install the 4 screws.



Hide 104.INSTALL FRONT WHEELS

Hide 105. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 106.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 107.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY