The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Map light assembly ·
Telephone microphone assembly ·
Radio and display receiver assembly ·
DCM (telematics transceiver)* ·
Harness or connector |
*: w/ Telematics Transceiver and for 6 Speakers
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
When replacing the DCM (telematics transceiver), make sure to replace it with a new one. (w/ Telematics Transceiver)
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Telematics Transceiver and for 6 Speakers | A |
| w/o Telematics Transceiver or for 9 Speakers | B |
A
B
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P14-4 (SNS2) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P20-6 (SNS2) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H6 DCM (telematics transceiver) connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-35 (MCI-) - P14-5 (MCO-) | Always | Below 1 Ω |
| H6-35 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-35 (MCI-) - P20-7 (MCO-) | Always | Below 1 Ω |
| H6-35 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(DCM [Telematics Transceiver]) |
Remove the DCM (telematics transceiver) with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-35 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P14-4 (SNS2) | Always | Below 1 Ω |
| G2-22 (MIN-) - P14-5 (MCO-) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| G2-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P20-6 (SNS2) | Always | Below 1 Ω |
| G2-22 (MIN-) - P20-7 (MCO-) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| G2-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | except TMMR Made |
| *B | for TMMR Made |
| *a | Component without harness connected
(Map Light Assembly) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (SNS2) - 5 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | except TMMR Made |
| *B | for TMMR Made |
| *a | Component without harness connected
(Map Light Assembly [Wire Harness Side]) |
| *b | Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side]) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (SNS2) - C-1 (SNS2) | Always | Below 1 Ω |
| 6 (MCO-) - C-2 (MIC-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (SNS2) - C-1 (SNS2) | Always | Below 1 Ω |
| 5 (MCO-) - C-2 (MIC-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG