Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2019.09–2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B1571  Green LED Error  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (green) illuminates after the ignition switch is turned to ON.

If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.

If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1571 Green LED Error Current for the manual (SOS) switch indicator (green) exceeds malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light sub-assembly (manual (SOS) switch)

·

Harness or connector



WIRING DIAGRAM

E354565E49
1.229,0.958 1.823,1.156 0.594,0.198 10 false GREEN 2.979,0.604 3.323,0.969 0.344,0.365 10 false 23 2.979,1.156 3.438,1.427 0.458,0.271 10 false 14 2.521,0.594 3.135,0.792 0.615,0.198 10 false IND2 2.458,1.156 3.073,1.354 0.615,0.198 10 false GND3 0.875,2.063 1.333,2.26 0.458,0.198 10 false P20 0.885,2.219 2.927,2.656 2.042,0.438 10 false Map Light Sub-assembly 4.896,0.594 5.208,0.792 0.313,0.198 10 false 12 4.896,1.156 5.208,1.354 0.313,0.198 10 false 26 5.167,0.708 5.781,0.906 0.615,0.198 10 false IND2 5.167,1.156 5.781,1.354 0.615,0.198 10 false SIG- 4.635,2.083 5.573,2.385 0.938,0.302 10 false H6 4.635,2.281 6.927,2.677 2.292,0.396 10 false Telephone Transceiver Assembly 1,1.677 3.042,2.115 2.042,0.438 10 false Manual (SOS) Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
2.INSPECT MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
a.
E434921C02
1.448,0.219 1.885,0.479 0.438,0.26 2.25,1.438 2.365,1.875 2.365,1.875 2.542,1.875 true 1.167,1.438 1.021,1.885 1.021,1.885 0.844,1.885 true 0.083,0.063 0.313,0.313 0.229,0.25 10 false *a 2.594,1.802 3.094,2.031 0.5,0.229 10 false GND3 0.51,1.802 0.948,2.052 0.438,0.25 10 false IND2 1.552,0.25 2.01,0.448 0.458,0.198 10 false P20
*a Component with harness connected
(Map Light Sub-assembly (Manual (SOS) Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P20-23 (IND2) - P20-14 (GND3) 2 seconds after ignition switch turned to ON
→ Ignition switch off
8.5 to 10 V
→ Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)

NG

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH))
3.INSPECT MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)
a.
E434905C03
0.594,1.927 0.781,1.927 0.781,1.927 1.073,1.406 true 2.75,1.906 2.552,1.906 2.552,1.906 2.385,1.427 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.792,1.823 3.354,2.073 0.563,0.25 10 false GND3 0.24,1.844 0.677,2.052 0.438,0.208 10 false IND2
*a Component without harness connected
(Map Light Sub-assembly (Manual (SOS) Switch))


Remove the map light sub-assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from batteries to terminal 23 (IND2) and a negative (-) lead to terminal 14 (GND3) of the map light sub-assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch indicator (green) comes on.

OK:

Manual (SOS) switch indicator (green) illuminates.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH)

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the H6 telephone transceiver assembly connector.


b.

Disconnect the P20 map light sub-assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-12 (IND2) - P20-23 (IND2) Always Below 1 Ω
H6-12 (IND2) or P20-23 (IND2) - Body ground Always 10 kΩ or higher
H6-26 (SIG-) - P20-14 (GND3) Always Below 1 Ω
H6-26 (SIG-) or P20-14 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT