This DTC is stored when a communication telematics box signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1572 | Microphone Error | Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON | ·
Telephone transceiver assembly ·
Communication telematics box*1 ·
Telephone Micro phone Assembly*2 ·
Harness or connector ·
Mayday wire*1 ·
Map light sub-assembly |
*1: w/ Communication telematics box
*2: w/o Communication telematics box
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds.
Turn the GTS on.
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Communication Telematics Box) | B |
| NG (w/o Communication Telematics Box) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the H6 telephone transceiver assembly connector.
Disconnect the P18 mayday wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-14 (MCMD) - P18-1 (MCMD) | Always | Below 1 Ω |
| H6-20 (SP+) - P18-3 (SP+) | Always | Below 1 Ω |
| H6-21 (SP-) - P18-9 (SP-) | Always | Below 1 Ω |
| H6-31 (MICV) - P18-6 (MICV) | Always | Below 1 Ω |
| H6-33 (MCVD) - P18-11 (MIC1) | Always | Below 1 Ω |
| H6-34 (MCI+) - P18-10 (MIC2) | Always | Below 1 Ω |
| H6-35 (MCI-) - P18-5 (MCI-) | Always | Below 1 Ω |
| H6-14 (MCMD) or P18-1 (MCMD) - Body ground | Always | 10 kΩ or higher |
| H6-20 (SP+) or P18-3 (SP+) - Body ground | Always | 10 kΩ or higher |
| H6-21 (SP-) or P18-9 (SP-) - Body ground | Always | 10 kΩ or higher |
| H6-31 (MICV) or P18-6 (MICV) - Body ground | Always | 10 kΩ or higher |
| H6-33 (MCVD) or P18-11 (MIC1) - Body ground | Always | 10 kΩ or higher |
| H6-34 (MCI+) or P18-10 (MIC2) - Body ground | Always | 10 kΩ or higher |
| H6-35 (MCI-) or P18-5 (MCI-) - Body ground | Always | 10 kΩ or higher |
| H6-32 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Wire Harness) |
| *b | Component without harness connected
(Communication Telematics Box) |
Disconnect the P18 wire harness connector.
Disconnect the P communication telematics box connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P18-1 (MCMD) - P-1 (MCMD) | Always | Below 1 Ω |
| P18-3 (SP+) - P-3 (SP+) | Always | Below 1 Ω |
| P18-9 (SP-) - P-8 (SP-) | Always | Below 1 Ω |
| P18-6 (MICV) - P-5 (MICV) | Always | Below 1 Ω |
| P18-10 (MIC2) - P-2 (MIC1+) | Always | Below 1 Ω |
| P18-11 (MIC1) - P-7 (MIC2+) | Always | Below 1 Ω |
| P18-5 (MCI-) - P-4 (MCI-) | Always | Below 1 Ω |
| P18-1 (MCMD) or P-1 (MCMD) - Body ground | Always | 10 kΩ or higher |
| P18-3 (SP+) or P-3 (SP+) - Body ground | Always | 10 kΩ or higher |
| P18-9 (SP-) or P-8 (SP-) - Body ground | Always | 10 kΩ or higher |
| P18-6 (MICV) or P-5 (MICV) - Body ground | Always | 10 kΩ or higher |
| P18-10 (MIC2) or P-2 (MIC1+) - Body ground | Always | 10 kΩ or higher |
| P18-11 (MIC1) or P-7 (MIC2+) - Body ground | Always | 10 kΩ or higher |
| P18-5 (MCI-) or P-4 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-31 (MICV) - Body ground | Ignition switch ACC | 4 to 6 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-35 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the communication telematics box with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the H6 telephone transceiver assembly connector.
Disconnect the P20 map light sub-assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-33 (MCVD) - P20-9 (MACC) | Always | Below 1 Ω |
| H6-34 (MCI+) - P20-8 (MCO+) | Always | Below 1 Ω |
| H6-35 (MCI-) - P20-7 (MCO-) | Always | Below 1 Ω |
| H6-33 (MCVD) or P20-9 (MACC) - Body ground | Always | 10 kΩ or higher |
| H6-34 (MCI+) or P20-8 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H6-35 (MCI-) or P20-7 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H6-32 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H6-33 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Sub-assembly) |
Remove the map light sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-9 (MACC) - B-5 (MACC) | Always | Below 1 Ω |
| A-8 (MCO+) - B-3 (MIC+) | Always | Below 1 Ω |
| A-7 (MCO-) - B-2 (MIC-) | Always | Below 1 Ω |
| A-9 (MACC) - A-8 (MCO+) | Always | 10 kΩ or higher |
| A-9 (MACC) - A-7 (MCO-) | Always | 10 kΩ or higher |
| A-8 (MCO+) - A-7 (MCO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT