Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2019.09–2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B15C5  Emergency Switch Error (Open or Short)  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short circuit in the manual (SOS) switch.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C5 Emergency Switch Error (Open or Short) Open or short circuit in the manual (SOS) switch is detected
·

Telephone transceiver assembly

·

Map light sub-assembly (manual (SOS) switch)

·

Harness or connector



WIRING DIAGRAM

E354792E31
0.927,2.042 1.385,2.24 0.458,0.198 10 false P20 0.927,2.229 2.958,2.635 2.031,0.406 10 false Map Light Sub-assembly 4.667,2.073 5.656,2.271 0.99,0.198 10 false H6 4.667,2.25 6.958,2.583 2.292,0.333 10 false Telephone Transceiver Assembly 2.521,0.604 3.135,0.802 0.615,0.198 10 false SIG1 5.156,0.646 5.771,0.844 0.615,0.198 10 false SIG1 2.469,1.177 3.083,1.375 0.615,0.198 10 false GND3 5.156,1.156 5.771,1.354 0.615,0.198 10 false SIG- 2.969,0.583 3.146,0.781 0.177,0.198 10 false 22 2.948,1.167 3.167,1.396 0.219,0.229 10 false 14 4.896,0.625 5.208,0.823 0.313,0.198 10 false 27 4.875,1.177 5.188,1.375 0.313,0.198 10 false 26 1.031,1.667 3.063,2.073 2.031,0.406 10 false Manual (SOS) Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH)
2.INSPECT MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH)
a.
E434905C04
2.792,1.917 2.604,1.917 2.604,1.917 2.375,1.427 true 0.844,1.948 1.042,1.948 1.042,1.948 1.208,1.417 true 0.115,0.094 0.385,0.313 0.271,0.219 10 false *a 2.854,1.833 3.365,2.115 0.51,0.281 10 false GND3 0.469,1.865 0.885,2.073 0.417,0.208 10 false SIG1
*a Component without harness connected
(Map Light Sub-assembly (Manual (SOS) Switch))


Remove the map light sub-assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
22 (SIG1) - 14 (GND3) Manual (SOS) switch not pressed 392 to 432 Ω
22 (SIG1) - 14 (GND3) Manual (SOS) switch pressed 78 to 86 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH)

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the H6 telephone transceiver assembly connector.


b.

Disconnect the P20 map light sub-assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-27 (SIG1) - P20-22 (SIG1) Always Below 1 Ω
H6-26 (SIG-) - P20-14 (GND3) Always Below 1 Ω
H6-27 (SIG1) or P20-22 (SIG1) - Body ground Always 10 kΩ or higher
H6-26 (SIG-) or P20-14 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT