Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › from 2019.09
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370279 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

Using this circuit, the radio receiver assembly sends power to the map light assembly, and the map light assembly sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM

E402684E09
2.188,1.594 2.656,1.781 0.469,0.188 10 false MACC 2.198,0.75 2.677,0.938 0.479,0.188 10 false MCO+ 2.229,1.156 2.635,1.365 0.406,0.208 10 false MCO- 2.24,2.354 2.708,2.542 0.469,0.188 10 false SNS2 0.448,3.083 2.698,3.302 2.25,0.219 10 false Telephone Microphone Assembly 0.302,3.563 0.667,3.75 0.365,0.188 10 false P20 0.302,3.719 1.646,3.948 1.344,0.229 10 false Map Light Assembly 0.385,4.26 1.313,4.5 0.927,0.24 10 false *: Shielded 5.802,3.708 6.813,4.24 1.01,0.531 10 false Radio Receiver Assembly 5.76,3.51 6.125,3.698 0.365,0.188 10 false G67 5.823,1.688 6.292,1.875 0.469,0.188 10 false MACC 5.844,0.875 6.313,1.063 0.469,0.188 10 false MIN+ 5.833,1.271 6.302,1.458 0.469,0.188 10 false MIN- 5.823,2.083 6.292,2.271 0.469,0.188 10 false SGND 5.833,2.438 6.302,2.625 0.469,0.188 10 false SNS2 0.479,2.917 0.948,3.104 0.469,0.188 10 false A 4.094,2 4.563,2.188 0.469,0.188 10 false * 5.552,0.75 5.729,0.938 0.177,0.188 10 false 5 5.5,1.167 5.781,1.365 0.281,0.198 10 false 19 5.542,1.583 5.813,1.792 0.271,0.208 10 false 4 5.479,1.969 5.76,2.167 0.281,0.198 10 false 18 5.542,2.333 5.823,2.531 0.281,0.198 10 false 6 2.01,1.177 2.49,1.365 0.479,0.188 10 false 2 2.01,0.76 2.49,0.948 0.479,0.188 10 false 3 2,1.594 2.479,1.781 0.479,0.188 10 false 5 2.01,2.354 2.49,2.542 0.479,0.188 10 false 1 2.708,0.76 3.188,0.948 0.479,0.188 10 false 8 2.719,1.188 3.198,1.375 0.479,0.188 10 false 7 2.729,1.583 3.208,1.771 0.479,0.188 10 false 9 2.719,2.354 3.198,2.542 0.479,0.188 10 false 6

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G67 radio receiver assembly connector.


b.

Disconnect the P20 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G67-5 (MIN+) - P20-8 (MCO+) Always Below 1 Ω
G67-19 (MIN-) - P20-7 (MCO-) Always Below 1 Ω
G67-4 (MACC) - P20-9 (MACC) Always Below 1 Ω
G67-6 (SNS2) - P20-6 (SNS2) Always Below 1 Ω
G67-5 (MIN+) - Body ground Always 10 kΩ or higher
G67-19 (MIN-) - Body ground Always 10 kΩ or higher
G67-4 (MACC) - Body ground Always 10 kΩ or higher
G67-6 (SNS2) - Body ground Always 10 kΩ or higher
G67-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO RECEIVER ASSEMBLY
a.
E237416C23
1.448,0.448 1.865,0.677 0.417,0.229 2.25,1.771 2.719,0.865 true 2.219,2 2.5,2.667 true 1.333,2.615 2.052,1.979 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.51,0.479 1.823,0.677 0.313,0.198 10 false G67 2.781,0.771 3.281,1 0.5,0.229 10 false MACC 2.542,2.594 3.01,2.771 0.469,0.177 10 false SGND 1,2.521 1.333,2.76 0.333,0.24 10 false MIN-
*a Component with harness connected
(Radio Receiver Assembly)


Remove the radio receiver assembly with its connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G67-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G67-18 (SGND) - Body ground Always Below 1 Ω
G67-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

3.INSPECT RADIO RECEIVER ASSEMBLY
a.
E436309C01
1.208,0.188 1.375,0.188 1.375,0.188 1.677,0.948 true 2.292,0.208 2.094,0.208 2.094,0.208 1.833,0.969 true 2.385,0.135 3,0.333 0.615,0.198 10 false SNS2 0.781,0.104 1.396,0.302 0.615,0.198 10 false MCO- 0.083,0.063 0.698,0.26 0.615,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly)


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO RECEIVER ASSEMBLY)

NG

7.CHECK MAP LIGHT ASSEMBLY
4.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO RECEIVER ASSEMBLY)
a.
E434909C06
1.573,0.313 1.948,0.563 0.375,0.25 1.5,1.438 1.208,0.448 1.208,0.448 1.042,0.448 true 1.656,1.438 2.26,0.26 2.26,0.26 2.417,0.26 true 0.583,0.365 1.198,0.563 0.615,0.198 10 false MCO+ 2.49,0.177 3.104,0.375 0.615,0.198 10 false MCO- 1.635,0.354 2.25,0.552 0.615,0.198 10 false P20 2.813,3.438 3.427,3.635 0.615,0.198 10 false GND 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a
*a Component with harness connected
(Map Light Assembly)


Remove the map light assembly with the connector(s) still connected.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Turn the ignition switch to ACC.


c.

Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the P20 map light assembly connector.


d.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal P20-8 (MCO+) - P20-7 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm (4.92 in.) from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT MAP LIGHT ASSEMBLY
5.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the A telephone microphone assembly connector.


c.
E434906C06
1.521,3.052 1.917,3.302 0.396,0.25 1.625,1.74 1.344,0.563 1.344,0.563 1.156,0.563 true 1.479,1.74 1.198,0.771 1.198,0.771 1.01,0.771 true 0.146,0.208 0.458,0.406 0.313,0.198 10 false *a 1.667,3.094 1.979,3.292 0.313,0.198 10 false A 0.208,2.99 0.521,3.188 0.313,0.198 10 false *b 0.719,0.469 1.292,0.708 0.573,0.24 10 false MCO- 0.594,0.688 1.167,0.927 0.573,0.24 10 false MCO+
*a Component without harness connected
(Map Light Assembly)
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (MCO+) - A-3 Always Below 1 Ω
7 (MCO-) - A-2 Always Below 1 Ω
P14-6 (MCO+) - P14-5 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

6.CHECK MAP LIGHT ASSEMBLY
6.CHECK MAP LIGHT ASSEMBLY
a.

Replace the map light assembly with a new or known good one and check that the malfunction disappears.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL

Result:
Proceed to
OK
NG


OK:

Malfunction disappears.




OK

END (MAP LIGHT ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO RECEIVER ASSEMBLY

7.CHECK MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the A telephone microphone assembly connector.


c.
E434906C07
1.521,3.052 1.917,3.302 0.396,0.25 1.781,1.74 2.177,0.604 2.177,0.604 2.375,0.604 true 1.625,1.74 1.344,0.563 1.344,0.563 1.156,0.563 true 1.406,3.844 1.208,4.177 1.208,4.177 1.021,4.177 true 1.573,3.854 1.344,4.385 1.344,4.385 1.156,4.385 true 0.146,0.208 0.458,0.406 0.313,0.198 10 false *a 1.667,3.094 1.979,3.292 0.313,0.198 10 false A 0.563,4.094 1.063,4.313 0.5,0.219 10 false SNS2 2.448,0.552 3.021,0.792 0.573,0.24 10 false SNS2 0.208,2.99 0.521,3.188 0.313,0.198 10 false *b 0.719,0.469 1.292,0.708 0.573,0.24 10 false MCO- 0.813,4.302 1.292,4.51 0.479,0.208 10 false MIC-
*a Component without harness connected
(Map Light Assembly [Wire Harness Side])
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (MCO-) - A-2 Always Below 1 Ω
6 (SNS2) - A-1 Always Below 1 Ω
P14-5 (MCO-) - P14-4 (SNS2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG