The main body ECU (multiplex network body ECU) operates the tilt sensor (theft warning ultrasonic and tilt sensor) via the ISIF communication line. The tilt sensor (theft warning ultrasonic and tilt sensor) sends information regarding changes in the vehicle tilt angle to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) checks whether the vehicle body is being tilted without authorization.
In the following situations, the tilt sensor (theft warning ultrasonic and tilt sensor) may operate and cause the theft deterrent system to operate even when the sensor is normal.
The vehicle is transported by a ferry, trailer or train.
The vehicle is parked in a multi-story parking facility.
The vehicle is washed by an automatic car wash.
A tire blows out.
The vehicle is jacked up for a tire or wheel change.
An earthquake occurs or the road subsides.
Goods such as skis or snowboards are loaded or unloaded.
Inspect the fuses for circuits related to this system before performing the following procedure.
w/ Entry and Start System:
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Intrusion Sensor | Status of the tilt sensor (theft warning ultrasonic and tilt sensor) detection | ON or OFF | ON: Vehicle tilt detected by sensor
OFF: Both of the conditions below is met ·
No moving object detected by sensor ·
Vehicle tilt not detected by sensor |
- |
| Tester Display |
|---|
| Intrusion Sensor |
| *1 | Map Light Sub-assembly |
| *a | Intrusion Sensor (Theft Warning Ultrasonic and Tilt Sensor) |
| *b | Protective Tape |
Be sure to cover the 2 intrusion sensors in the map light sub-assembly with protective tape to prevent detected by the intrusion sensor.
After setting the theft deterrent system, wait 30 seconds or more (until the vehicle is in the armed state), tilt the vehicle and confirm the Data List (jack up the vehicle so that the tires are in the air).
When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).*
*: w/ Entry and Start System
The display on the GTS changes according to the detection condition of the tilt sensor (theft warning ultrasonic and tilt sensor).
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected (Map Light Sub-assembly) | *b | IOUT Initial Signal |
| *c | IOUT Initial Response | *d | Approximately 1.0 second |
| *e | Initial Diagnosis | *f | Approximately 1.0 to 1.6 seconds |
| *g | Approximately 0.05 seconds | *h | Approximately 5.5 seconds |
| *i | Disarmed State | *j | Arming Preparation State |
| Tester Connection | Content |
|---|---|
| Tester Connection | P20-3 (IOUT) - Body ground |
| Tool Setting | 2 V/DIV., 100 ms./DIV. |
| Condition | Theft deterrent system is set (system changes from disarmed state to arming preparation state) |
If the tilt sensor (theft warning ultrasonic and tilt sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).
If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).
The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the G45 main body ECU (multiplex network body ECU) connector.
Disconnect the P20 map light sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G45-14 (ISIF) - P20-3 (IOUT) | Always | Below 1 Ω |
| G45-14 (ISIF) - Body ground | Always | 10 kΩ or higher |
| P20-3 (IOUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG