Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › 2019.02–2020.08
RM3620E _57 Power Source / Network _076180 POWER DISTRIBUTION _0371061 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of main body ECU (multiplex network body ECU) Code registration
·

Wireless door lock control system (for Entry function, HV model)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:
(Click here)
for M20A-FKS:
(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
w/ Entry and Start System:

Replacement of main body ECU (multiplex network body ECU)


Code registration
·

Wireless door lock control system (for Entry function, Gasoline model)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method.

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.



NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Do not remove the main body ECU (multiplex network body ECU) except when replacing it.

·

When removing the main body ECU (multiplex network body ECU), always replace it with a new one.



Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73900 6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (except Manual Transaxle)

Hide 55308B 7.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (except Manual Transaxle)

a.
E405814

Detach the 2 wire harness clamps.


b.
E405815C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the nut, bolt and No. 3 instrument panel to cowl brace sub-assembly.


Hide 8.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (except Manual Transaxle)

a.
E405816C01
2.365,1.74 2.552,1.917 0.188,0.177 10 true *a
*a w/ Clearance Warning System


Detach the 2 wire harness clamps.


b.

w/ Clearance Warning System:

i.

Disconnect the 5 connectors.



c.

w/o Clearance Warning System:

i.

Disconnect the 4 connectors.



d.
E405817C01
1.823,0.646 2.354,0.646 true 1.813,1.083 2.115,1.083 2.115,1.083 2.115,0.656 true 2.427,0.563 2.625,0.75 0.198,0.188 10 true *a
*a Lever Connector
V113147

Rotate in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.


e.

Detach the wire harness clamp.


f.

Disconnect the 2 connectors.


g.
E405818

Disconnect the 5 connectors.


h.
E405819

Remove the 2 nuts.


i.

Detach the claw and disconnect the instrument panel junction block assembly with main body ECU.


j.
E405820

Detach the claw and remove the instrument panel junction block assembly with main body ECU from the connector holder.


k.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.

E405821C01
1.052,1.729 1.385,1.729 1.385,1.729 1.385,2.906 true 1.042,2.208 1.385,2.208 true 1.281,2.958 1.594,3.115 0.313,0.156 10 false *a
*a Lever Connector - -
V113147

Rotate in this Direction
V100155

Protective Tape



l.

Detach the wire harness clamp and remove the instrument panel junction block assembly with main body ECU.


Hide 89221 9.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (except Manual Transaxle)

a.
E405822

Detach the claw and remove the junction block bracket from the instrument panel junction block assembly with main body ECU.


b.

Press the lock of the instrument panel junction block assembly and release the lock of the main body ECU (multiplex network body ECU) as shown in the illustration.

E403056C01
4.271,4.479 4.698,4.479 false 4.906,5.146 4.906,4.708 false 4.854,5.188 5.167,5.344 0.313,0.156 10 false *a 4.083,4.396 4.396,4.552 0.313,0.156 10 false *b
*a Instrument Panel Junction Block Assembly *b Main Body ECU (Multiplex Network Body ECU)
V113147

Movement Direction
V100155

Instrument Panel Junction Block Assembly Lock



c.

While pressing the lock, horizontally insert a thin-bladed screwdriver with its tip wrapped with protective tape between the main body ECU (multiplex network body ECU) and instrument panel junction block assembly.

NOTICE:

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).


E403057C01
0,0 0,0 false
V113147

Horizontally Insert a Thin-bladed Screwdriver
V100155

Protective Tape



d.
E403058C01
0.615,1.604 1.229,1.604 true 0.427,1.521 0.74,1.677 0.313,0.156 10 false *a
*a Internal Connector
V113147

Insert a Thin-bladed Screwdriver in this Direction
V113148

Released in this Direction
V100155

Protective Tape


When the thin-bladed screwdriver with its tip wrapped with protective tape is inserted, the internal connector lock is released.

NOTICE:
·

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).

·

Do not excessively insert the screwdriver. Otherwise, the internal connector terminals may become deformed or damaged.

·

Replace the instrument panel junction block assembly when the connector terminal, the locking section, or the case is damaged or deformed.




e.
E403059

Hold the rib of the main body ECU (multiplex network body ECU).


f.
E403060C01
0,0 0,0 false
V113147

Rotate in this Direction


While rotating the main body ECU (multiplex network body ECU), completely release the lock.


g.
E403061C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


Hide 58810J 10.REMOVE CONSOLE BOX ASSEMBLY (for Manual Transaxle)

Hide 67913B 11.REMOVE FRONT DOOR SCUFF PLATE RH (for Manual Transaxle)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111C 12.REMOVE COWL SIDE TRIM BOARD RH (for Manual Transaxle)

Hide 55607 13.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for Manual Transaxle)

Hide 55550 14.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for Manual Transaxle)

Hide 55433B 15.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for Manual Transaxle)

Hide 16.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Manual Transaxle)

a.
E405597

Disconnect the connector.


b.

Detach the 2 wire harness clamps.


c.
E405916C01
0.865,0.698 1.49,0.698 true 1.094,0.698 1.094,1.208 1.094,1.208 1.479,1.208 true 0.625,0.594 0.823,0.792 0.198,0.198 10 true *a
*a Lever Connector
V113147

Rotate in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.


d.

Disconnect the 2 connectors.


e.
E405917

Disconnect the 3 connectors.


f.
E405575C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the nut, bolt and disconnect the ECU integration box RH.


g.
E405598C01
0,0 0,0 false
V113147

Slide in this Direction


Slide the ECU integration box RH in the direction indicated by the arrow shown in the illustration.


h.
E405918C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the nut and bolt.


i.

Detach the claw and disconnect the instrument panel junction block assembly with main body ECU.


j.
E405572

Detach the 2 wire harness clamps.


k.
E407017C01
0,0 0,0 false
V113147

Rotate in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw, disconnect the 2 lever connectors and remove the instrument panel junction block assembly with main body ECU.


Hide 89221 17.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for Manual Transaxle)

a.

Press the lock of the instrument panel junction block assembly and release the lock of the main body ECU (multiplex network body ECU) as shown in the illustration.

E405591C01
4.396,4.479 4.823,4.479 false 5.063,5.104 5.063,4.667 false 5,5.146 5.313,5.302 0.313,0.156 10 false *a 4.219,4.396 4.531,4.552 0.313,0.156 10 false *b
*a Instrument Panel Junction Block Assembly *b Main Body ECU (Multiplex Network Body ECU)
V113147

Movement Direction
V100155

Instrument Panel Junction Block Assembly Lock



b.

While pressing the lock, horizontally insert a thin-bladed screwdriver with its tip wrapped with protective tape between the main body ECU (multiplex network body ECU) and instrument panel junction block assembly.

NOTICE:

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).


E405592C01
0,0 0,0 false
V113147

Horizontally Insert a Thin-bladed Screwdriver
V100155

Protective Tape



c.
E405593C01
0.552,1.583 1.167,1.583 true 0.365,1.5 0.677,1.656 0.313,0.156 10 false *a
*a Internal Connector
V113147

Insert a Thin-bladed Screwdriver in this Direction
V113148

Released in this Direction
V100155

Protective Tape


When the thin-bladed screwdriver with its tip wrapped with protective tape is inserted, the internal connector lock is released.

NOTICE:
·

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).

·

Do not excessively insert the screwdriver. Otherwise, the internal connector terminals may become deformed or damaged.

·

Replace the instrument panel junction block assembly when the connector terminal, the locking section, or the case is damaged or deformed.




d.
E405594

Hold the rib of the main body ECU (multiplex network body ECU).


e.
E405595C01
0,0 0,0 false
V113147

Rotate in this Direction


While rotating the main body ECU (multiplex network body ECU), completely release the lock.


f.
E405596C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.