Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY (for LITHIUM-ION BATTERY) › from 2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425014 HV BATTERY(for LITHIUM-ION BATTERY) A

HYBRID / BATTERY CONTROL  HV BATTERY(for LITHIUM-ION BATTERY)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

HINT:

This procedure is only performed when the hole plug is being replaced with a new one.


a.

Install the hole plug to the vehicle body.


Hide G9510 2.INSTALL HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the 2 guide pins to install the HV battery to the vehicle body.


b.
A462080C01
0.958,0.083 1.188,0.26 0.229,0.177 10 true *b 2.896,0.125 3.125,0.302 0.229,0.177 10 true *a 3.177,1.958 3.406,2.135 0.229,0.177 10 true *a 0.156,1.938 0.385,2.115 0.229,0.177 10 true *a
*a Bolt (A)
(Bolt Length: 25 mm (0.984 in.))
*b Bolt (B)
(Bolt Length: 24 mm (0.945 in.))


Install the HV battery to the vehicle body with the 3 bolts (A) and bolt (B).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.

·

As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.

·

If the HV battery has been struck or dropped, replace it.




Hide 82161 3.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the HV battery connector.


Hide G92PF 4.INSTALL NO. 4 HV BATTERY PROTECTOR

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the clamp to install the No. 4 HV battery protector to the HV battery.


Hide 82161 5.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the 2 clamps to connect the floor wire to the HV battery.


Hide G9290A 7.INSTALL HYBRID BATTERY HOSE ASSEMBLY

a.
A462081

Engage the 2 claws to install the hybrid battery hose assembly to the HV battery.


b.

Connect the hybrid battery hose assembly to the vehicle body.


Hide 82161 8.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the HV battery junction block assembly connector.


b.

Connect the electric vehicle battery plug assembly connector.


c.

Engage the clamp.


Hide 821H1 9.CONNECT HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the shield ground to the HV battery.


b.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 10.INSTALL NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Be sure to wear insulated gloves.


a.
A462082C01
1.104,1.125 1.375,1.125 false 0.542,0.583 0.698,0.583 0.698,0.583 0.792,0.927 false 0.781,0.104 1.094,0.302 0.313,0.198 10 false *b 0.365,0.5 0.677,0.698 0.313,0.198 10 false *a 1.406,1.042 1.719,1.24 0.313,0.198 10 false *1
*1 Battery Cover Lock Striker
*a Button
*b Push


Install the No. 1 HV battery cover panel RH to the HV battery with the 3 bolts and 3 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Install the battery cover lock striker, then push the button to lock it.


Hide G9230 11.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 13.PERFORM INITIALIZATION