Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY) › from 2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425052 HYBRID CONTROL SYSTEM(for 4WD/AWD with LITHIUM-ION BATTERY) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD with LITHIUM-ION BATTERY)  Shut Down Signal Circuit  


DESCRIPTION

The cause of the malfunction may be a shutdown signal.

Check whether there is a shutdown signal +B short circuit.

Related Parts Check
Area Inspection
HSDN terminal Check that the HSDN terminal voltage decreases to check for an open or short circuit while READY off (IG ON).
Hybrid vehicle control ECU assembly, inverter, wire harness Check for open or short circuit in hybrid vehicle control ECU assembly, inverter and wire harness.

SYSTEM DESCRIPTION

Power supply to the motor is cut off due to a shutdown signal sent from the hybrid vehicle control ECU assembly to the motor generator control ECU (MG ECU).

WIRING DIAGRAM

for LHD:
A306450E62
2.417,0.344 2.729,0.542 0.313,0.198 10 false 36 2.417,0.698 2.729,0.896 0.313,0.198 10 false 35 2.417,1.073 2.729,1.271 0.313,0.198 10 false 6 2.417,1.396 2.729,1.594 0.313,0.198 10 false 9 2.417,1.75 2.729,1.948 0.313,0.198 10 false 8 4.542,1.021 4.854,1.219 0.313,0.198 10 false 6 4.552,1.51 4.865,1.708 0.313,0.198 10 false 3 3.333,0.49 4.813,0.771 1.479,0.281 10 false from PCU Fuse 4.469,1.208 4.781,1.406 0.313,0.198 10 false A29 4.792,1.073 5.323,1.323 0.531,0.25 10 false HSDN 4.813,1.688 5.344,1.938 0.531,0.25 10 false E1 4.729,2.271 7.146,2.667 2.417,0.396 10 false Hybrid Vehicle Control ECU Assembly 1.948,1.083 2.479,1.333 0.531,0.25 10 false HSDN 2.052,0.792 2.583,1.042 0.531,0.25 10 false +B2 2.125,0.458 2.656,0.708 0.531,0.25 10 false +B 1.927,1.51 2.458,1.76 0.531,0.25 10 false GND1 1.927,1.844 2.458,2.094 0.531,0.25 10 false GND2 0.469,2.219 0.99,2.448 0.521,0.229 10 false A87 0.469,2.365 2.646,2.594 2.177,0.229 10 false Inverter with Converter Assembly 4.469,1.688 4.75,1.885 0.281,0.198 10 false A30

for RHD:
A306450E64
2.417,0.344 2.729,0.542 0.313,0.198 10 false 36 2.417,0.698 2.729,0.896 0.313,0.198 10 false 35 2.417,1.073 2.729,1.271 0.313,0.198 10 false 6 2.417,1.396 2.729,1.594 0.313,0.198 10 false 9 2.417,1.75 2.729,1.948 0.313,0.198 10 false 8 4.542,1.021 4.854,1.219 0.313,0.198 10 false 6 4.552,1.51 4.865,1.708 0.313,0.198 10 false 3 3.333,0.49 4.813,0.771 1.479,0.281 10 false from PCU Fuse 4.469,1.208 4.781,1.406 0.313,0.198 10 false A29 4.792,1.073 5.323,1.323 0.531,0.25 10 false HSDN 4.813,1.688 5.344,1.938 0.531,0.25 10 false E1 4.729,2.271 7.146,2.667 2.417,0.396 10 false Hybrid Vehicle Control ECU Assembly 1.948,1.083 2.479,1.333 0.531,0.25 10 false HSDN 2.052,0.792 2.583,1.042 0.531,0.25 10 false +B2 2.125,0.458 2.656,0.708 0.531,0.25 10 false +B 1.927,1.51 2.458,1.76 0.531,0.25 10 false GND1 1.927,1.844 2.458,2.094 0.531,0.25 10 false GND2 0.469,2.219 0.99,2.448 0.521,0.229 10 false A87 0.469,2.365 2.646,2.594 2.177,0.229 10 false Inverter with Converter Assembly 4.469,1.688 4.75,1.885 0.281,0.198 10 false G63

Refer to the wiring diagram for the ECU power source circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>ECU Power Source Circuit

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
a.

Turn the power switch on (IG).


b.

for LHD:

Measure the voltage according to the value(s) in the table below.

C407546C53
1.563,0.344 1.906,0.594 0.344,0.25 5.313,0.302 5.656,0.552 0.344,0.25 6.01,1.302 5.771,2.26 true 1.781,1.292 1.427,2.25 true 0.385,0.281 0.698,0.479 0.313,0.198 10 false *a 1.615,0.396 2.073,0.594 0.458,0.198 10 false A29 5.354,0.354 5.635,0.594 0.281,0.24 10 false A30 5.719,2.292 6.031,2.49 0.313,0.198 10 false E1 1.24,2.302 1.854,2.5 0.615,0.198 10 false HSDN 0.125,0.083 0.438,0.281 0.313,0.198 10 false *A
*A for LHD - -
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A29-6 (HSDN) - A30-3 (E1) Power switch on (IG) Below 4.5 V



c.

for RHD:

Measure the voltage according to the value(s) in the table below.

C407546C54
1.563,0.344 1.906,0.594 0.344,0.25 5.313,0.302 5.656,0.552 0.344,0.25 6.01,1.302 5.771,2.26 true 1.781,1.292 1.427,2.25 true 0.385,0.281 0.698,0.479 0.313,0.198 10 false *a 1.615,0.396 2.073,0.594 0.458,0.198 10 false A29 5.354,0.354 5.635,0.594 0.281,0.24 10 false G63 5.719,2.292 6.031,2.49 0.313,0.198 10 false E1 1.24,2.302 1.854,2.5 0.615,0.198 10 false HSDN 0.125,0.083 0.438,0.281 0.313,0.198 10 false *A
*A for RHD - -
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A29-6 (HSDN) - G63-3 (E1) Power switch on (IG) Below 4.5 V



d.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

SHUTDOWN SIGNAL CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INVERTER WITH CONVERTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A87 inverter with converter assembly connector.


c.

Disconnect the A29 hybrid vehicle control ECU assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
C412487C03
0.073,3.385 0.438,3.635 0.365,0.25 0.167,1.219 0.531,1.469 0.365,0.25 2.021,1.542 2.25,2.063 true 2.094,1.531 2.688,2.063 true 2.615,2.76 2.438,3.458 true 1.688,3.479 1.948,2.813 true 2.188,0.573 1.823,1.135 true 1.51,3.469 1.208,2.833 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.146,2.354 0.458,2.552 0.313,0.198 10 false *b 0.24,1.281 0.698,1.479 0.458,0.198 10 false A87 0.135,3.438 0.594,3.635 0.458,0.198 10 false A29 2.188,2.104 2.802,2.302 0.615,0.198 10 false +B2 2.208,0.385 2.823,0.583 0.615,0.198 10 false HSDN 1.906,2.625 2.521,2.823 0.615,0.198 10 false HSDN 0.865,2.656 1.479,2.854 0.615,0.198 10 false MREL 2.677,2.083 3.292,2.281 0.615,0.198 10 false +B 2.531,2.573 3.146,2.771 0.615,0.198 10 false +B1
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A87-6 (HSDN) or A29-6 (HSDN) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU assembly and inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A87-6 (HSDN) - A87-36 (+B) Power switch off 10 kΩ or higher
A87-6 (HSDN) - A87-35 (+B2) Power switch off 10 kΩ or higher
A29-6 (HSDN) - A29-11 (+B1) Power switch off 10 kΩ or higher
A29-6 (HSDN) - A29-5 (MREL) Power switch off 10 kΩ or higher



j.

Reconnect the A29 hybrid vehicle control ECU assembly connector.


k.

Reconnect the A87 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A87 inverter with converter assembly connector.


c.
C410406C03
1.479,1.854 1.031,1.333 true 0.917,1.344 0.542,1.833 true 1.573,0.417 1.219,0.969 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.604,0.25 2.219,0.448 0.615,0.198 10 false HSDN 0.354,1.865 0.667,2.063 0.313,0.198 10 false +B 1.479,1.865 1.938,2.063 0.458,0.198 10 false +B2
*a Component without harness connected
(Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (HSDN) - 36 (+B) Power switch off 10 kΩ or higher
6 (HSDN) - 35 (+B2) Power switch off 10 kΩ or higher



d.

Reconnect the A87 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG