Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425055 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P0ABF28  Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

Refer to the description for DTC P0ABF11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>P0ABF11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure The offset value of the battery current sensor is excessively large.
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery ECU assembly

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0ABF28 Hybrid/EV Battery Current

HINT:
·

Make sure to perform Current Sensor Offset Learning after replacing a battery current sensor.

·

This DTC may be output if Current Sensor Offset Learning has not been completed.



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle on urban roads for approximately 10 minutes.

7.

Turn the power switch off and wait for 2 minutes or more.

8.

Turn the power switch on (IG) and turn the GTS on.

9.

With power switch on (IG) and wait for 10 seconds or more.

10.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

11.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
"P0ABF28" only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid battery system in the table below are output. B
DTCs of hybrid control system in the table below are output. C


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P062F46 Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


e.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)

B

C

2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)

OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

OK

4.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
C433532N01
2.188,0.823 2.604,1.073 0.417,0.25 2.271,0.854 2.563,1.052 0.292,0.198 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
C433531N01
0.406,0.823 0.823,1.104 0.417,0.281 0.479,0.875 0.781,1.073 0.302,0.198 10 true z25

Disconnect the z25 battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A407530C07
1.49,0.115 1.906,0.365 0.417,0.25 1.531,3.021 1.948,3.271 0.417,0.25 2.271,2.042 2.969,2.594 true 1.844,3.948 2.344,3.677 true 2.188,2.021 2.76,0.542 true 1.063,4.438 1.594,4.198 true 2.302,1.917 2.938,0.813 true 2.323,4.365 1.833,4.188 true 2.281,2.177 2.833,2.75 true 1.615,3.938 1.021,3.698 true 0.281,0.052 0.771,0.583 0.49,0.531 10 false *a 0.813,2.969 1.281,3.417 0.469,0.448 10 false *b 1.583,0.135 2.073,0.667 0.49,0.531 10 false z26 1.635,3.052 2.125,3.583 0.49,0.531 10 false z25 3.042,2.573 3.354,2.823 0.313,0.25 10 false IB1 2.813,0.427 3.302,0.958 0.49,0.531 10 false GIB 3,0.719 3.344,1.094 0.344,0.375 10 false IB0 2.875,2.74 3.333,3.052 0.458,0.313 10 false VIB 2.375,3.625 2.688,3.875 0.313,0.25 10 false IB1 0.833,4.406 1.208,4.656 0.375,0.25 10 false GIB 2.354,4.385 2.833,4.615 0.479,0.229 10 false IB0 0.792,3.625 1.25,3.938 0.458,0.313 10 false VIB
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z26-24 (IB1) - z25-2 (IB1) Power switch off Below 1 Ω
z26-23 (GIB) - z25-3 (GIB) Power switch off Below 1 Ω
z26-12 (IB0) - z25-4 (IB0) Power switch off Below 1 Ω
z26-36 (VIB) - z25-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z26-24 (IB1) or z25-2 (IB1) - Body ground and other terminals Power switch off 10 kΩ or higher
z26-23 (GIB) or z25-3 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
z26-12 (IB0) or z25-4 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z26-36 (VIB) or z25-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Reconnect the z25 battery current sensor connector to the HV battery junction block assembly.


g.

Reconnect the z26 battery ECU assembly connector.


h.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

5.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB0))

NG

10.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
5.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
C435216C01
1.458,2.333 1.885,2.594 0.427,0.26 1.885,3.479 2.49,3.177 true 1.854,3.948 2.656,4.188 true 0.115,0.094 0.396,0.323 0.281,0.229 10 true *a 1.563,2.375 1.927,2.594 0.365,0.219 10 false z25 2.552,3.094 3.073,3.542 0.521,0.448 10 false VIB 2.74,4.146 3.156,4.469 0.417,0.323 10 false GIB
*a Component with harness connected
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z25-1 (VIB) - z25-3 (GIB) Power switch on (IG)

NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the toyota electrical tester to 40 V when performing this test.




f.
C435216C03
1.458,2.333 1.885,2.594 0.427,0.26 1.5,3.938 0.927,4.104 true 1.885,3.917 2.521,4.167 true 0.115,0.094 0.396,0.323 0.281,0.229 10 true *a 1.552,2.385 2.083,2.938 0.531,0.552 10 false z25 0.594,4.094 1.115,4.542 0.521,0.448 10 false IB0 2.635,4.156 3.052,4.479 0.417,0.323 10 false GIB
*a Component with harness connected
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Using a toyota electrical tester set to 4 V, measure the IB0 voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z25-4 (IB0) - z25-3 (GIB) Power switch on (IG)

NOTICE:

Be sure to set the toyota electrical tester to 4 V when performing this test.



g.

Compare the measured values of the IB0 terminal voltage and VIB terminal voltage using the following formula:

IB0 voltage - 0.56 X VIB Voltage = less than 0.084 V
IB0 voltage - 0.56 X VIB Voltage = -0.084 V or higher


Result:
Result Proceed to
Within the specified range above A
Other than above B


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Install the No. 1 HV battery cover panel RH.



A

6.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB1))

B

6.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB1))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
C435216C01
1.458,2.333 1.885,2.594 0.427,0.26 1.885,3.479 2.49,3.177 true 1.854,3.948 2.656,4.188 true 0.115,0.094 0.396,0.323 0.281,0.229 10 true *a 1.563,2.375 1.927,2.594 0.365,0.219 10 false z25 2.552,3.094 3.073,3.542 0.521,0.448 10 false VIB 2.74,4.146 3.156,4.469 0.417,0.323 10 false GIB
*a Component with harness connected
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z25-1 (VIB) - z25-3 (GIB) Power switch on (IG)

NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the toyota electrical tester to 40 V when performing this test.




f.
C435216C02
1.458,2.333 1.885,2.594 0.427,0.26 1.552,3.51 1.021,3.271 true 1.885,3.917 2.521,4.167 true 0.115,0.094 0.396,0.323 0.281,0.229 10 true *a 1.563,2.375 2.021,2.76 0.458,0.385 10 false z25 0.802,3.188 1.323,3.635 0.521,0.448 10 false IB1 2.635,4.156 3.052,4.479 0.417,0.323 10 false GIB
*a Component with harness connected
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Using a toyota electrical tester set to 4 V, measure the IB1 voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z25-2 (IB1) - z25-3 (GIB) Power switch on (IG)

NOTICE:

Be sure to set the toyota electrical tester to 4 V when performing this test.



g.

Compare the measured values of the IB1 terminal voltage and VIB terminal voltage using the following formula:

Condition
IB1 voltage - 0.44 X VIB Voltage = less than 0.078 V
IB1 voltage - 0.44 X VIB Voltage = -0.078 V or higher


Result:
Result Proceed to
Within the specified range above. A
Other than above B


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Install the No. 1 HV battery cover panel RH.



A

7.REPLACE BATTERY ECU ASSEMBLY

B

7.REPLACE BATTERY ECU ASSEMBLY

NEXT

8.SIMULATION TEST
8.SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Trouble Codes.


d.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

e.

Drive the vehicle on urban roads for approximately 10 minutes.


f.

Turn the power switch off and wait for 2 minutes or more.


g.

Turn the power switch on (IG) and wait for 10 seconds or more.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT (HV BATTERY)
9.CHECK DTC OUTPUT (HV BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
DTCs are not output. A
P0ABF28 is also output. B



e.

Turn the power switch off.



A

END

B

10.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
C433550N01
0.927,0.927 1.313,1.177 0.385,0.25 1.021,0.948 1.24,1.146 0.219,0.198 10 true A

Disconnect the A No. 1 HV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Check the terminals of the male side of the A No. 1 HV supply stack sub-assembly connector.

OK:

The terminals are free of foreign matter and not damaged.



Result:
Proceed to
OK
NG


e.

Reconnect the A No. 1 HV supply stack sub-assembly connector.


f.

Install the No. 1 HV battery hose.



OK

NG

11.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

OK

NG

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY AND NO. 2 HV SUPPLY STACK SUB-ASSEMBLY