Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY (for LITHIUM-ION BATTERY) › 2020.05–2020.08
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425014 HV BATTERY(for LITHIUM-ION BATTERY) A

HYBRID / BATTERY CONTROL  HV BATTERY(for LITHIUM-ION BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of HV battery
1.

Battery status info update

2.

Prediagnostic battery charge

3.

Battery diagnosis


HV battery status information cannot be updated for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of hybrid battery terminal block High voltage fuse accumulated load history reset DTCs are stored for 2WD:(Click here)
for 4WD/AWD:(Click here)
·

Replacement of battery ECU assembly

·

Replacement of HV battery junction block assembly


Current sensor offset learning (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.


·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When the cable is disconnected from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

If the HV battery has been struck or dropped, replace it.

·

When connecting a connector to the HV battery, confirm that the connector is securely connected through the following:

- Push the connector until a click sound is heard.

- Visually check and confirm that the connector is securely connected by pulling on it.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·

When performing repairs around the HV battery, such as using a tap, do not allow metal shavings to enter the HV battery.

·

Do not touch any high voltage wire harnesses, connectors or parts with bare hands.

·
A462070

Hold the areas shown in the illustration and lift the HV battery.

·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the HV battery.

·
A462071C01
0.719,1.792 0.938,1.792 0.938,1.792 1.135,2.208 true 0.51,0.188 0.74,0.188 0.74,0.188 0.927,0.604 true 0.313,0.083 0.625,0.281 0.313,0.198 10 false *a 0.521,1.688 0.833,1.885 0.313,0.198 10 false *a
*a Opening


Do not put your hands into the openings of the HV battery.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Do not climb on top of or stand on the HV battery.

·

Do not allow any foreign matter or water to enter the HV battery.

·

If any bolts, nuts or clips are dropped into the HV battery, make sure to remove them.



HINT:

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.


PROCEDURE

Hide 1. READ VALUE USING TECHSTREAM

a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid/EV Battery Temperature 1 to 6.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid/EV Battery Temperature 1
Hybrid/EV Battery Temperature 2
Hybrid/EV Battery Temperature 3
Hybrid/EV Battery Temperature 4
Hybrid/EV Battery Temperature 5
Hybrid/EV Battery Temperature 6
50003 397 198,199,200,201,202,203

d.

Read the Data List.

NOTICE:

If any of the temperatures listed in "Hybrid/EV Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.



Hide 82111 3.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 6.INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.
A430741C03
1.906,1.594 2.156,1.792 0.25,0.198 10 true *a 1.833,0.417 2.083,0.615 0.25,0.198 10 true *b
*a Bolt (A)
*b Bolt (B)


Using a T25 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (A).

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)

NOTICE:

Do not touch the waterproof seal of the connector cover assembly.



b.

Install the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 82111 7.CONNECT ENGINE ROOM MAIN WIRE

Hide G9230 8.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N4A 9.REMOVE NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Be sure to wear insulated gloves.


a.
A462072C01
0.5,0.99 0.646,0.99 0.646,0.99 0.875,0.771 false 0.979,1.135 1.115,0.938 1.115,0.938 1.24,0.938 true 1.094,0.271 1.396,0.271 false 1.083,1.281 1.385,1.281 false 0.292,0.906 0.5,1.094 0.208,0.188 10 false *a 0.24,0.531 0.448,0.719 0.208,0.188 10 false *b 1.302,0.875 1.51,1.063 0.208,0.188 10 false *c 1.458,0.219 1.667,0.406 0.208,0.188 10 false *1 1.438,1.219 1.646,1.406 0.208,0.188 10 false *2
*1 Service Plug Grip
*2 Battery Cover Lock Striker
*a Projection
*b Turn
*c Button


Using the service plug grip, remove the battery cover lock striker.

HINT:

Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.



b.

Remove the 3 bolts, 3 nuts and No. 1 HV battery cover panel RH from the HV battery.


Hide 821H1 10.DISCONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A462073C01
1.667,1.333 1.917,1.667 1.917,1.667 2.083,1.667 true 2.125,1.563 2.344,1.75 0.219,0.188 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.

Disconnect the shield ground from the HV battery.


Hide 82161 11.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A462076C01
2.542,0.333 2.854,0.531 0.313,0.198 10 true *a 0.552,0.958 0.865,1.156 0.313,0.198 10 true *b
*a Electric Vehicle Battery Plug Assembly Connector
*b HV Battery Junction Block Assembly Connector


Disengage the clamp.


b.

Disconnect the electric vehicle battery plug assembly connector.


c.

Disconnect the HV battery junction block assembly connector.


Hide G9290A 12.REMOVE HYBRID BATTERY HOSE ASSEMBLY

a.
A462077

Disconnect the hybrid battery hose assembly from the vehicle body.


b.

Disengage the 2 claws to remove the hybrid battery hose assembly from the HV battery.


Hide 899A0 13.REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Hide 82161 14.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A462814

Disengage the 2 clamps to disconnect the floor wire.


Hide G92PF 15.REMOVE NO. 4 HV BATTERY PROTECTOR

CAUTION:

Be sure to wear insulated gloves.


a.
A462078

Disengage the clamp to remove the No. 4 HV battery protector from the HV battery.


Hide 82161 16.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A462079

Disconnect the HV battery connector.


Hide G9510 17.REMOVE HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A462080

Remove the 4 bolts.

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.

·

When removing the HV battery from the vehicle, do not allow it to contact the vehicle.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Insulate the disconnected terminals or connectors with insulating tape.

·

If the HV battery has been struck or dropped, replace it.




b.
A462139

Disengage the 2 guide pins to remove the HV battery from the vehicle body.


Hide 18.REMOVE HOLE PLUG

HINT:

This procedure is only performed when the hole plug is being replaced with a new one.


a.
A462150

Remove the hole plug from the vehicle body.


Hide 19.PERFORM RECOVERY INSPECTION

a.

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION