The inlet air temperature sensor (battery) is mounted on the HV battery. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the inlet air temperature sensor are the same as those of the battery temperature sensors (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>P0A9B11). The battery voltage sensor uses signals from the inlet air temperature sensor to control the air volume of the battery cooling blower assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0AAC11 | Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground | The inlet air temperature sensor output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic) |
·
Hybrid battery thermistor ·
Battery voltage sensor ·
Wire harness or connector |
Does not come on | Master Warning:
Comes on |
| P0AAC15 | Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open | The inlet air temperature sensor output voltage is higher than the standard value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic) |
·
Hybrid battery thermistor ·
Battery voltage sensor ·
Wire harness or connector |
Does not come on | Master Warning:
Comes on |
After checking for the above DTCs, check the hybrid system Data List item "Hybrid Battery Cooling Fan Intake Air Temperature 1" using the GTS.
| Displayed Temperature | Malfunction |
|---|---|
| -45°C (-49°F) or less | Open or +B short circuit |
| 95°C (203°F) or more | GND short |
| DTC No. | Data List |
|---|---|
| P0AAC11 | Hybrid Battery Cooling Fan Intake Air Temperature 1 |
| P0AAC15 |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 5 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Refer to the wiring diagram for DTC P0A9B2A.
Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| "P0AFC00, P0AFC96 or P308A12" is not output. | A |
| "P0AFC00, P0AFC96 or P308A12" is also output. | B |
Turn the power switch off.
A
B
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery exhaust duct.
Check the connections of the z19 battery voltage sensor connector.
The connector is connected securely and there are no contact problems.
| Proceed to |
|---|
| OK |
| NG |
Install the No. 1 hybrid battery exhaust duct.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the upper HV battery cover sub-assembly.
Visually check the installation condition of the inlet air temperature sensor.
| Result | Proceed to |
|---|---|
| The inlet air temperature sensor is installed in the correct location and its claws are engaged securely. | A |
| The claws of the inlet air temperature sensor are damaged. | B |
| The inlet air temperature sensor is not installed correctly, but its claws are not damaged. | C |
Install the upper HV battery cover sub-assembly.
A
B
C
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery exhaust duct.
Disconnect the z19 battery voltage sensor connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Battery Voltage Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z19-1 (TC0) - z19-7 (GC0) | Power switch off
0 to 10°C (32 to 50°F) |
17.7 to 27.8 kΩ |
| z19-1 (TC0) - z19-7 (GC0) | Power switch off
10 to 20°C (50 to 68°F) |
12.0 to 18.2 kΩ |
| z19-1 (TC0) - z19-7 (GC0) | Power switch off
20 to 30°C (68 to 86°F) |
8.22 to 12.2 kΩ |
| z19-1 (TC0) - z19-7 (GC0) | Power switch off
30 to 40°C (86 to 104°F) |
5.74 to 8.41 kΩ |
| z19-1 (TC0) - z19-7 (GC0) | Power switch off
40 to 50°C (104 to 122°F) |
4.09 to 5.91 kΩ |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Disconnect the N72 battery voltage sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z19-1 (TC0) - N72-1 (IGCT) | Power switch off | 10 kΩ or higher |
| z19-1 (TC0) - N72-5 (GND) | Power switch off | 10 kΩ or higher |
| z19-7 (GC0) - N72-1 (IGCT) | Power switch off | 10 kΩ or higher |
| z19-7 (GC0) - N72-5 (GND) | Power switch off | 10 kΩ or higher |
| z19-4 (TB0) - N72-1 (IGCT) | Power switch off | 10 kΩ or higher |
| z19-4 (TB0) - N72-5 (GND) | Power switch off | 10 kΩ or higher |
| z19-10 (GB0) - N72-1 (IGCT) | Power switch off | 10 kΩ or higher |
| z19-10 (GB0) - N72-5 (GND) | Power switch off | 10 kΩ or higher |
| z19-3 (TB1) - N72-1 (IGCT) | Power switch off | 10 kΩ or higher |
| z19-3 (TB1) - N72-5 (GND) | Power switch off | 10 kΩ or higher |
| z19-9 (GB1) - N72-1 (IGCT) | Power switch off | 10 kΩ or higher |
| z19-9 (GB1) - N72-5 (GND) | Power switch off | 10 kΩ or higher |
| z19-2 (TB2) - N72-1 (IGCT) | Power switch off | 10 kΩ or higher |
| z19-2 (TB2) - N72-5 (GND) | Power switch off | 10 kΩ or higher |
| z19-8 (GB2) - N72-1 (IGCT) | Power switch off | 10 kΩ or higher |
| z19-8 (GB2) - N72-5 (GND) | Power switch off | 10 kΩ or higher |
Reconnect the N72 and z19 battery voltage sensor connectors.
Install the No. 1 hybrid battery exhaust duct.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the upper HV battery cover sub-assembly.
Check the wire harnesses and connectors of the battery temperature sensors and inlet air temperature sensor for abnormalities by sight and touch.
There are no open or short circuits in the wire harnesses and connectors. There are no short circuits to other wire harnesses.
Install the upper HV battery cover sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG