Refer to DTC P085011.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>P085011
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P085015 | Park/Neutral Switch Circuit Short to Battery or Open | The neutral position switch output voltage is higher than 4.88 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in neutral position switch circuit ·
Neutral position switch ·
ECM |
- | DTC stored | SAE: P0852 |
When the ignition switch is turned ON and the output voltage of the neutral position switch is higher than 4.88 V for 3 seconds or more, the ECM determines that the neutral position switch circuit is malfunctioning and stores a DTC.
| Required Sensors/Components | Neutral position switch |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P085015.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
Refer to DTC P085011.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>P085011
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Neutral Position Switch) |
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the neutral position switch connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C55-1 (W1) - C55-3 (F+) | Ignition switch ON | 4.5 to 5.5 V |
| C55-2 (TMN) - C55-3 (F+) | Ignition switch ON | 3.0 to 5.5 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C55-3 (F+) - Body ground | Ignition switch off | Below 1 Ω |
| C55-1 (W1) - C55-2 (TMN) | Ignition switch off | 0.95 to 1.05 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2WD: Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>NEUTRAL POSITION SWITCH>REMOVAL
for 4WD: Click hereDrivetrain>EG62F (MANUAL TRANSMISSION / TRANSAXLE)>NEUTRAL POSITION SWITCH>REMOVAL
NG
Disconnect the neutral position switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C55-2 (TMN) - C40-106 (NPSW) | Always | Below 1 Ω |
| C55-3 (F+) - C40-60 (ENPS) | Always | Below 1 Ω |
| C55-2 (TMN) or C40-106 (NPSW) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG