Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2020.08
RM3620E _51 Engine / Hybrid System _076696 A25A-FXS ENGINE MECHANICAL _0373302 REAR CRANKSHAFT OIL SEAL A

A25A-FXS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
Grille shutter switch specification infomation Vehicle control history (RoB) [X260E] is stored (Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
Front exhaust pipe assembly (w/ GPF) GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)(for 2WD)
(Click here)(for 4WD/AWD)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment Electronically controlled brake system
·

Reset memory

·

Calibration


VSC malfunction (Click here)(w/ vacuum brake booster)
(Click here)(w/o vacuum brake booster)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

NOTICE:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 2.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly horizontal.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A407561N02
1.521,0.896 1.167,0.479 1.167,0.479 1.927,0.656 true 0.74,0.354 1.115,0.552 0.375,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A406362

Remove the 6 bolts and transmission input damper assembly from the flywheel sub-assembly.


Hide 13405 3.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A407561N03
1.521,0.896 1.167,0.479 1.167,0.479 1.927,0.656 true 0.74,0.354 1.115,0.552 0.375,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.
A406363

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


Hide 19315 4.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A472675

Remove the No. 1 crankshaft position sensor plate.


Hide 11401L 5.REMOVE REAR ENGINE OIL SEAL

a.
A400434C01
2.896,1.531 2.896,1.188 2.896,1.188 3.125,0.917 false 1.813,1.854 1.552,1.854 1.552,1.854 1.26,1.365 true 1.875,1.75 2.188,1.948 0.313,0.198 10 true *a 2.813,1.573 3.125,1.771 0.313,0.198 10 true *b
*a Protective Tape
*b Cut Position


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Be careful not to damage the crankshaft.


HINT:

Tape the screwdriver tip before use.