Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › from 2020.08
RM3620E _52 Drivetrain _076274 P710 HYBRID TRANSMISSION / TRANSAXLE _0371335 HYBRID VEHICLE TRANSAXLE A

P710 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM
for A25A-FXS(w/ Canister Pump Module):

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
for A25A-FXS(w/o Canister Pump Module):

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
for A25A-FXS:

Grille shutter switch specification infomation


Vehicle control history (RoB) [X260E] is stored w/ Canister Pump Module:
(Click here)
w/o Canister Pump Module:
(Click here)
for A25B-FXS:

Perform Vehicle Identification Number (VIN) or frame number registration


DTC P063051 is output (Click here)
for A25A-FXS:
·

Engine assembly

·

Air fuel ratio sensor (sensor 1)

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
for A25A-FXS(w/o Canister Pump Module):

Front exhaust pipe assembly*2


GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
for A25B-FXS:
·

Engine assembly

·

Air fuel ratio sensor (sensor 1)

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD with NICKEL METAL HYDRIDE BATTERY:(Click here)
for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY:(Click here)
for 2WD with LITHIUM-ION BATTERY:(Click here)
for 4WD/AWD with LITHIUM-ION BATTERY:(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for HV model) (Click here)
Replacement of the headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Front wheel alignment adjustment
·

Clear zero point calibration data.

·

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD with Nickel Metal Hydride Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 4WD/AWD with Nickel Metal Hydride Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 2WD with Lithium-ion Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>PRECAUTION

for 4WD/AWD with Lithium-ion Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

·

If the ECM has been struck or dropped, replace it.

·

for A25A-FXS:

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION

·

for A25B-FXS:

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



PROCEDURE

Hide 1. PERFORM RESOLVER INITIALIZATION

NOTICE:

If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.



Hide 2.REMOVE ENGINE ASSEMBLY WITH HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 45319 5.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 6.DISCONNECT WIRE HARNESS (for LHD)

Hide 7.DISCONNECT WIRE HARNESS (for RHD)

Hide 82121 8.DISCONNECT ENGINE WIRE (for LHD)

a.

Remove the 2 bolts.

C393903


b.

Disconnect the 5 clamps.


Hide 82121 9.DISCONNECT ENGINE WIRE (for RHD)

a.

Remove the 2 bolts.

C405643


b.

Disconnect the 4 clamps.


Hide 821H2 10.DISCONNECT HV AIR CONDITIONING WIRE

a.
C407306C01
0.063,0.073 0.323,0.281 0.26,0.208 10 true *A 0.104,2.406 0.365,2.625 0.26,0.219 10 true *B
*A for 2WD
*B for 4WD/AWD


for 2WD:

i.

Remove the bolt.


ii.

Detach the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.



b.

for 4WD/AWD:

i.

Remove the 2 bolts.


ii.

Detach the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.



Hide 28193 11.REMOVE STARTER HOLE INSULATOR

a.
C393908

Remove the 2 bolts and starter hole insulator from the engine assembly.


Hide 11363A 12.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C393909

Remove the flywheel housing side cover from the engine assembly.


Hide 51100H 13.REMOVE FRONT FRAME ASSEMBLY

Hide 12361 14.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
C393910

Remove the bolt and front engine mounting insulator from the transverse engine engine mounting bracket.


Hide 12311A 15.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C379391

Remove the 3 bolts and transverse engine engine mounting bracket from the hybrid vehicle transaxle assembly.


Hide 12371A 16.REMOVE REAR ENGINE MOUNTING INSULATOR

Hide 17.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C405620

Remove the bolt and wire harness clamp bracket from the rear engine mounting insulator.


Hide 12303 18.REMOVE REAR ENGINE MOUNTING BRACKET

a.
C379392

Remove the 4 bolts and rear engine mounting bracket from the hybrid vehicle transaxle assembly.


Hide 30900 19.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C379393

Remove the 8 bolts and hybrid vehicle transaxle assembly from the engine assembly.

NOTICE:
·

To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.

·

To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during hybrid vehicle transaxle assembly removal and installation.




Hide G125A 21.REMOVE MOTOR COOLING COOLER

Hide 33823 22.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C393911

Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.


Hide 44781E 23.REMOVE HOSE BRACKET

a.
C379403

Remove the 2 bolts and hose bracket from the hybrid vehicle transaxle assembly.


Hide 82125 24.REMOVE TRANSMISSION WIRE

a.
C379404

Disconnect the connector.


b.

Remove the bolt and transmission wire from the hybrid vehicle transaxle assembly.


Hide 25.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the 4 bolts and 4 wire harness clamp brackets from the hybrid vehicle transaxle assembly.

C393912


Hide 26.REMOVE TRANSAXLE HOUSING PLUG

a.
C379406

Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.


Hide 27.REMOVE STUD BOLT

a.
C379407

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.


Hide 33185B 28.REMOVE TRANSAXLE UNDER STOPPER BRACKET

a.
C407294

Remove the 4 bolts and transaxle under stopper bracket from the hybrid vehicle transaxle assembly.


Hide 35162B 29.REMOVE TRANSAXLE CASE PROTECTOR (for 4WD/AWD)

a.
C379408C01
2.271,0.76 1.948,0.76 true 2.302,0.688 2.51,0.865 0.208,0.177 10 true *1
*1 Clip


Remove the 2 bolts.


b.

Remove the clip and transaxle case protector from the hybrid vehicle transaxle assembly.