Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.08
RM3620E _51 Engine / Hybrid System _076696 A25A-FXS ENGINE MECHANICAL _0373304 ENGINE UNIT A

A25A-FXS ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
Grille shutter switch specification infomation Vehicle control history (RoB) [X260E] is stored (Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
Front exhaust pipe assembly (w/ GPF) GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)(for 2WD)
(Click here)(for 4WD/AWD)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment Electronically controlled brake system
·

Reset memory

·

Calibration


VSC malfunction (Click here)(w/ vacuum brake booster)
(Click here)(w/o vacuum brake booster)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

NOTICE:
·

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 43457 1.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A406682

Remove the 3 bolts and drive shaft bearing bracket.


Hide 88310 2.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

a.
E371430C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and 2 nuts.


b.
E371431

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor with motor assembly.


Hide 16207 3.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A406683

Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the outlet water by-pass sub-assembly.


b.

Remove the bolt and the No. 2 water by-pass pipe sub-assembly.


Hide 16260 4.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A406684

Remove the bolt.


b.
A406686

Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the water by-pass outlet sub-assembly.


c.
A409020

Remove the 2 bolts and water hose clamp bracket.


Hide 89481B 5.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ GPF)

Hide 25760 6.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY (w/ GPF)

Hide 25706 7.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)

Hide 17167 8.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

w/o GPF:

i.
A473063

Remove the 3 bolts and the No. 1 exhaust manifold heat insulator from the exhaust manifold.



b.

w/ GPF:

i.
A444949

Remove the 3 bolts and the No. 1 exhaust manifold heat insulator from the exhaust manifold.



Hide 17141 10.REMOVE EXHAUST MANIFOLD

a.

w/o GPF:

i.
A472677

Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold from the cylinder head sub-assembly.



b.

w/ GPF:

i.
A444950

Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold from the cylinder head sub-assembly.



c.
A406688

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 22030 11.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25680 12.REMOVE EGR COOLER ASSEMBLY

a.
A452723C01
1.479,0.875 1.458,0.354 1.458,0.354 1.271,0.354 true 2.292,0.99 2.677,0.438 2.677,0.438 2.844,0.438 true 2.854,0.333 3.094,0.521 0.24,0.188 10 true *1 1.073,0.25 1.313,0.448 0.24,0.198 10 true *2
*1 No. 3 Water By-pass Hose
*2 Water Hose


Slide the clip and disconnect the water hose from the EGR cooler assembly.


b.

Slide the clip and disconnect the No. 3 water by-pass hose from the EGR cooler assembly.


c.
A452724

Remove the 5 bolts, EGR cooler assembly, EGR cooler gasket and EGR valve gasket.


Hide 25601 13.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 14.REMOVE WATER HOSE

a.
A472678

Slide the clip and remove the water hose from the EGR valve assembly.


Hide 25620 15.REMOVE EGR VALVE ASSEMBLY

a.
A472679

Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.


b.
A469689

Using an 8 mm socket wrench, remove the bolt.


c.
A469690C01
2.135,0.76 2.323,0.5 2.323,0.5 2.469,0.5 true 2.135,0.854 2.448,0.854 true 2.438,0.76 2.75,0.958 0.313,0.198 10 true *a 2.458,0.406 2.771,0.604 0.313,0.198 10 true *b
*a Pin
*b Hole


Remove the EGR valve assembly vertically.


d.
A472682

Using an 8 mm socket wrench, remove the bolt and EGR valve bracket.


Hide 16279 16.REMOVE NO. 3 WATER BY-PASS PIPE

a.
A406695

Using an 8 mm socket wrench, remove the bolt and No. 3 water by-pass pipe from the intake manifold.


b.

Slide the clip and disconnect the No. 3 water by-pass pipe from the water outlet.


Hide 16278 17.REMOVE NO. 2 WATER BY-PASS PIPE

a.
A406696N02
1.813,0.958 1.969,1.156 0.156,0.198 10 true B 1.125,1.604 1.281,1.802 0.156,0.198 10 true B 2.615,1.885 2.771,2.083 0.156,0.198 10 true A

Remove the bolt (A).


b.

Using an 8 mm socket wrench, remove the 2 bolts (B) and No. 2 water by-pass pipe.


Hide 17177 19.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23901 20.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 21.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A472683C01
0,0 0,0 false
V100135

Union Nut
V100136

Bolt


Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


b.

Remove the bolt and No. 1 fuel pipe sub-assembly.


Hide 23100X 22.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16295 23.REMOVE NO. 7 WATER BY-PASS HOSE

a.
A406697

Slide the 2 clips and remove the No. 7 water by-pass hose.


Hide 82219A 24.REMOVE SENSOR WIRE

a.
A406698

Disconnect the 4 connectors.


b.

Detach the 3 clamps.


c.

Using an 8 mm socket wrench, remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.


Hide 82126A 25.REMOVE NO. 6 ENGINE WIRE

a.
A406699

Disconnect the 4 connectors.


b.

Detach the 2 clamps.


c.

Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.


Hide 26.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A406700

Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.


Hide 23807 27.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 28.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 29.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 31.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 33.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452 36.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A400314

Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the cylinder head sub-assembly.


c.
A400321

Remove the O-ring from the engine oil level dipstick guide.


Hide 17169A 37.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.
A450484

Remove the bolt and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.