The DCM (telematics transceiver) sends a mute signal to the radio and display receiver assembly.
The radio and display receiver assembly controls the volume according to the mute signal from the DCM (telematics transceiver).
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for TMMR Made | A |
| except TMMR Made | B |
A
B
| *a | Component with harness connected
(DCM [Telematics Transceiver]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-17 (MUTE) - Body ground | Ignition switch ACC
Audio system playing → Emergency call mode |
2.0 V or higher
→ Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the H6 DCM (telematics transceiver) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-3 (TMUT) - H6-17 (MUTE) | Always | Below 1 Ω |
| G2-3 (TMUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the DCM (telematics transceiver) connector.
| *a | Front view of wire harness connector
(to DCM [Telematics Transceiver]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H6-17 (MUTE) - Body ground | Ignition switch ON | 2.0 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(DCM [Telematics Transceiver]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H10-14 (MUTE) - Body ground | Ignition switch ON
Audio system playing → Emergency call mode |
2.0 V or higher
→ Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the H10 DCM (telematics transceiver) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-3 (TMUT) - H10-14 (MUTE) | Always | Below 1 Ω |
| G2-3 (TMUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the DCM (telematics transceiver) connector.
| *a | Front view of wire harness connector
(to DCM [Telematics Transceiver]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H10-14 (MUTE) - Body ground | Ignition switch ON | 2.0 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG