The radio and display receiver assembly, telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the DCM (telematics transceiver) sends power to telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the DCM (telematics transceiver).*
*: w/ Telematics Transceiver and for 6 Speakers
When replacing the DCM (telematics transceiver), make sure to replace it with a new one. (w/ Telematics Transceiver)
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.
When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Result | Proceed to |
|---|---|
| NG (w/o Telematics Transceiver or for 9 Speakers) | A |
| NG (w/ Telematics Transceiver and for 6 Speakers) | B |
| OK | C |
A
B
C
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P14-4 (SNS2) | Always | Below 1 Ω |
| G2-23 (MACC) - P14-7 (MACC) | Always | Below 1 Ω |
| G2-21 (MIN+) - P14-6 (MCO+) | Always | Below 1 Ω |
| G2-22 (MIN-) - P14-5 (MCO-) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| G2-23 (MACC) - Body ground | Always | 10 kΩ or higher |
| G2-21 (MIN+) - Body ground | Always | 10 kΩ or higher |
| G2-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| G2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P20-6 (SNS2) | Always | Below 1 Ω |
| G2-23 (MACC) - P20-9 (MACC) | Always | Below 1 Ω |
| G2-21 (MIN+) - P20-8 (MCO+) | Always | Below 1 Ω |
| G2-22 (MIN-) - P20-7 (MCO-) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| G2-23 (MACC) - Body ground | Always | 10 kΩ or higher |
| G2-21 (MIN+) - Body ground | Always | 10 kΩ or higher |
| G2-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| G2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Remove the radio and display receiver assembly with the connector(s) still connected.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G2-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-24 (SGND) - Body ground | Always | Below 1 Ω |
| G2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for TMMR Made
*2: except TMMR Made
| *A | except TMMR Made |
| *B | for TMMR Made |
| *a | Component with harness connected
(Map Light Assembly) |
Remove the map light assembly with the connector(s) still connected.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect an oscilloscope to terminals 6 (MCO+) and 5 (MCO-) of the P14 map light assembly connector.*1
Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the P20 map light assembly connector.*2
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | P14-6 (MCO+) - P14-5 (MCO-)
P20-8 (MCO+) - P20-7 (MCO-)*2 |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm (4.92 in.) from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | except TMMR Made |
| *B | for TMMR Made |
| *a | Component without harness connected
(Map Light Assembly [Wire Harness Side]) |
| *b | Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side]) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P14-4 (SNS2) - A-1 (SNS2) | Always | Below 1 Ω |
| P14-7 (MACC) - A-5 (MACC) | Always | Below 1 Ω |
| P14-6 (MCO+) - A-3 (MIC+) | Always | Below 1 Ω |
| P14-5 (MCO-) - A-2 (MIC-) | Always | Below 1 Ω |
| P14-4 (SNS2) - Body ground | Always | 10 kΩ or higher |
| P14-7 (MACC) - Body ground | Always | 10 kΩ or higher |
| P14-6 (MCO+) - Body ground | Always | 10 kΩ or higher |
| P14-5 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P20-6 (SNS2) - A-1 (SNS2) | Always | Below 1 Ω |
| P20-9 (MACC) - A-5 (MACC) | Always | Below 1 Ω |
| P20-8 (MCO+) - A-3 (MIC+) | Always | Below 1 Ω |
| P20-7 (MCO-) - A-2 (MIC-) | Always | Below 1 Ω |
| P20-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| P20-9 (MACC) - Body ground | Always | 10 kΩ or higher |
| P20-8 (MCO+) - Body ground | Always | 10 kΩ or higher |
| P20-7 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P14-4 (SNS2) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P20-6 (SNS2) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the H6*1 or H10*2 DCM (telematics transceiver) connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-21 (MIN+) - H6-18 (MCO+) | Always | Below 1 Ω |
| G2-22 (MIN-) - H6-19 (MCO-) | Always | Below 1 Ω |
| G2-21 (MIN+) - Body ground | Always | 10 kΩ or higher |
| G2-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| G2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-21 (MIN+) - H10-16 (MCO+) | Always | Below 1 Ω |
| G2-22 (MIN-) - H10-32 (MCO-) | Always | Below 1 Ω |
| G2-21 (MIN+) - Body ground | Always | 10 kΩ or higher |
| G2-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| G2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for TMMR Made
*2: except TMMR Made
Disconnect the H6*1 or H10*2 DCM (telematics transceiver) connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-33 (MCVD) - P14-7 (MACC) | Always | Below 1 Ω |
| H6-34 (MCI+) - P14-6 (MCO+) | Always | Below 1 Ω |
| H6-35 (MCI-) - P14-5 (MCO-) | Always | Below 1 Ω |
| H6-33 (MCVD) - Body ground | Always | 10 kΩ or higher |
| H6-34 (MCI+) - Body ground | Always | 10 kΩ or higher |
| H6-35 (MCI-) - Body ground | Always | 10 kΩ or higher |
| H6-32 (SGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H10-5 (MCVD) - P20-9 (MACC) | Always | Below 1 Ω |
| H10-6 (MCI+) - P20-8 (MCO+) | Always | Below 1 Ω |
| H10-7 (MCI-) - P20-7 (MCO-) | Always | Below 1 Ω |
| H10-5 (MCVD) - Body ground | Always | 10 kΩ or higher |
| H10-6 (MCI+) - Body ground | Always | 10 kΩ or higher |
| H10-7 (MCI-) - Body ground | Always | 10 kΩ or higher |
| H10-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H6*1 or H10*2 DCM (telematics transceiver) connector.
*1: for TMMR Made
*2: except TMMR Made
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-24 (SGND) - Body ground | Always | Below 1 Ω |
| G2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H6*1 or H10*2 DCM (telematics transceiver) connector.
*1: for TMMR Made
*2: except TMMR Made
| *A | for TMMR Made |
| *B | except TMMR Made |
| *a | Component with harness connected
(DCM [Telematics Transceiver]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H6-33 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H10-5 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-35 (MCI-) - Body ground | Always | Below 1 Ω |
| H6-32 (SGND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H10-7 (MCI-) - Body ground | Always | Below 1 Ω |
| H10-23 (SGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for TMMR Made
*2: except TMMR Made
| *A | except TMMR Made |
| *B | for TMMR Made |
| *a | Component with harness connected
(Map Light Assembly) |
Remove the map light assembly with the connector(s) still connected.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect an oscilloscope to terminals 6 (MCO+) and 5 (MCO-) of the P14 map light assembly connector.*1
Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the P20 map light assembly connector.*2
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | P14-6 (MCO+) - P14-5 (MCO-)
P20-8 (MCO+) - P20-7 (MCO-)*2 |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm (4.92 in.) from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for TMMR Made
*2: except TMMR Made
| *A | for TMMR Made |
| *B | except TMMR Made |
| *a | Component with harness connected
(DCM [Telematics Transceiver]) |
Remove the DCM (telematics transceiver) with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Connect an oscilloscope to terminal H6-18 (MCO+) and H6-19 (MCO-).*1
Connect an oscilloscope to terminal H10-16 (MCO+) and H10-32 (MCO-).*2
Turn the ignition switch to ACC.
Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | H6-18 (MCO+) - H6-19 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Ignition switch ACC 2.
Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover. |
| Item | Condition |
|---|---|
| Measurement terminal | H10-16 (MCO+) - H10-32 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Ignition switch ACC 2.
Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG