Home › Engine / Hybrid System › A25A-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2020.08
RM3620E _51 Engine / Hybrid System _076480 A25A-FKS INTAKE / EXHAUST _0372147 EXHAUST MANIFOLD A

A25A-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold, No. 1 upper front floor heat insulator and No. 1 exhaust manifold heat insulator.

HINT:

At this time, do not install the parts with bolts or nuts.



c.
A402260N01
1.729,0.719 1.906,0.917 0.177,0.198 10 true 1 0.938,0.052 1.115,0.25 0.177,0.198 10 true 2 2.385,0.042 2.563,0.24 0.177,0.198 10 true 3 1.396,0.656 1.573,0.854 0.177,0.198 10 true 4 2.656,0.281 2.833,0.479 0.177,0.198 10 true 5 1.01,0.844 1.188,1.042 0.177,0.198 10 true 6 0.323,0.063 0.5,0.26 0.177,0.198 10 true 7

Using a 12 mm deep socket wrench, temporarily install the exhaust manifold to the cylinder head sub-assembly with 7 new nuts.


d.

Using the 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A401948N01
2.927,1.167 3.083,1.365 0.156,0.198 10 true 1 0.906,1.375 1.063,1.563 0.156,0.188 10 true 2

Temporarily install the manifold stay to the exhaust manifold and cylinder block sub-assembly with the bolt and nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A406431C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
Specified tightening torque : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.8 N*m (90 kgf*cm, 78 in.*lbf)




Hide 58151 5.INSTALL NO. 1 UPPER FRONT FLOOR HEAT INSULATOR

a.

Install the No. 1 upper front floor heat insulator to the vehicle body with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 6.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 89467B 7.INSTALL AIR FUEL RATIO SENSOR (for Sensor 1)

Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install 2 new gaskets to the front exhaust pipe assembly.


b.

Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.


c.

Install the front exhaust pipe assembly to the exhaust manifold and tail exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


d.
A432694C01
2.542,0.479 2.625,0.208 2.625,0.208 2.75,0.208 true 2.198,0.719 2.448,0.938 2.448,0.938 2.615,0.729 true 2.771,0.115 2.958,0.313 0.188,0.198 10 true *a 2.385,0.958 2.573,1.135 0.188,0.177 10 true *b
*a Tie Band
*b Wire Harness Clamp


Connect the air fuel ratio sensor (for Sensor 2) connector.


e.

Attach the 2 wire harness clamps so that the tie band is positioned as shown in the illustration.


Hide 10.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY