Home › Engine / Hybrid System › A25B-FXS (FUEL) › FUEL PUMP (for High Pressure) › from 2020.08
RM3620E _51 Engine / Hybrid System _080118 A25B-FXS FUEL _0391735 FUEL PUMP(for High Pressure) A

A25B-FXS FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
·

Replacement of fuel pump assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 4.REMOVE REAR NO. 2 FLOOR BOARD

Hide 65351A 5.REMOVE BATTERY HOLE COVER

Hide 6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 22030 7.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 23901 8.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A405321

Remove the fuel pipe clamp from the fuel tube connector.


b.
A405244

Disconnect the fuel tube sub-assembly from the fuel pump assembly and fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 16278 9.REMOVE NO. 2 WATER BY-PASS PIPE

a.
A405316

Detach the clamp and disconnect the HV air conditioning wire.


b.
A405317

Slide the clip and disconnect the No. 8 water by-pass hose from the No. 2 water by-pass pipe.


c.
A405318N02
1.188,0.302 1.313,0.458 0.125,0.156 10 true A 0.885,0.958 1.01,1.115 0.125,0.156 10 true A 2.146,1.323 2.271,1.479 0.125,0.156 10 true B

Remove the 2 bolts (A) and disconnect the No. 2 water by-pass pipe from the intake manifold.


d.

Remove the bolt (B) and No. 2 water by-pass pipe from the cylinder block sub-assembly.


Hide 23801P 10.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.


a.
A405311

Disconnect the connector from the ignition coil assembly.


b.
A469542C01
0,0 0,0 false
V100135

Union Nut
V100136

Bolt


Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


c.

Remove the bolt.


d.
A405247

Loosen the 2 bolts of the fuel pump assembly.


e.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.


Hide 23100X 11.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

NOTICE:

When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


a.
A405248

Disconnect the connector from the fuel pump assembly.


b.
A405249

Remove the 2 bolts, fuel pump assembly and fuel pump flange from the cylinder head cover sub-assembly.


c.
A401723

Remove the O-ring from the fuel pump assembly.


d.
A405250

Remove the fuel pump lifter assembly from the fuel pump lifter guide.


e.
A405251

Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.