Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL › from 2020.08
RM3620E _51 Engine / Hybrid System _076696 A25A-FXS ENGINE MECHANICAL _0373301 FRONT CRANKSHAFT OIL SEAL A

A25A-FXS ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
Grille shutter switch specification infomation Vehicle control history (RoB) [X260E] is stored (Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
Front exhaust pipe assembly (w/ GPF) GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)(for 2WD)
(Click here)(for 4WD/AWD)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment Electronically controlled brake system
·

Reset memory

·

Calibration


VSC malfunction (Click here)(w/ vacuum brake booster)
(Click here)(w/o vacuum brake booster)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

NOTICE:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 13470 2.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 11301C 3.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A406358C03
0.563,1.313 1.677,1.313 true 0.385,1.208 0.698,1.406 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, pry out the timing chain cover oil seal.

NOTICE:

After removal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.


HINT:

Tape the screwdriver tip before use.