Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM3620E _51 Engine / Hybrid System _076696 A25A-FXS ENGINE MECHANICAL _0373303 ENGINE ASSEMBLY A

A25A-FXS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
Grille shutter switch specification infomation Vehicle control history (RoB) [X260E] is stored (Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
Front exhaust pipe assembly (w/ GPF) GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)(for 2WD)
(Click here)(for 4WD/AWD)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment Electronically controlled brake system
·

Reset memory

·

Calibration


VSC malfunction (Click here)(w/ vacuum brake booster)
(Click here)(w/o vacuum brake booster)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

NOTICE:
·

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD

Hide 65351A 4.REMOVE BATTERY HOLE COVER

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58441J 6.REMOVE BATTERY SERVICE HOLE COVER

Hide 8.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 9. DISCHARGE FUEL SYSTEM PRESSURE

Hide 10. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 11.SECURE STEERING WHEEL

Hide 12.REMOVE FRONT WHEELS

Hide 53896B 13.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

a.

for Short Type:

i.
A434180

Remove the 3 screws.


ii.

Detach the clip and remove the front fender front splash shield LH.



b.

for Long Type:

i.
A434222

Remove the 4 screws.


ii.

Detach the clip and remove the front fender front splash shield LH.



Hide 53895B 14.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

a.

for Short Type:

i.
A434181

Remove the 3 screws.


ii.

Detach the clip and remove the front fender front splash shield RH.



b.

for Long Type:

i.
A434223

Remove the 4 screws.


ii.

Detach the clip and remove the front fender front splash shield RH.



Hide 51441 15.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the 2 bolts and 8 screws. (Short Type Front Fender Front Splash Shield)


b.

Remove the 2 bolts and 6 screws. (Long Type Front Fender Front Splash Shield)


c.

Detach the guide and remove the No. 1 engine under cover.

A474576C02
1.75,2.365 1.948,2.542 0.198,0.177 10 true *a 5,2.24 5.198,2.417 0.198,0.177 10 true *a
*a Short Type Front Fender Front Splash Shield - -
V100135

Bolt
V100136

Screw



Hide 51420 16.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

a.
A434183C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Clip


Remove the 2 bolts, 2 screws, 6 clips and No. 2 engine under cover assembly.


Hide 53737D 17.REMOVE FRONT FENDER APRON SEAL LH

a.
A434185C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Remove the 2 bolts, clip and front fender apron seal LH.


Hide 53736E 18.REMOVE FRONT FENDER APRON SEAL RH

a.
A434186C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Remove the 2 bolts, clip and front fender apron seal RH.


Hide 20.REMOVE HEADLIGHT ASSEMBLY LH

Hide 52618 21.REMOVE FRONT LOWER BUMPER ABSORBER

a.
A434202

Remove the clip.


b.

Detach the claws and remove the front lower bumper absorber.


Hide 52132A 22.REMOVE FRONT BUMPER NO. 2 REINFORCEMENT

Hide 23.DRAIN ENGINE COOLANT (for Engine)

Hide 12601B 26.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

for LHD:

i.
A434187

Lift the front of the No. 1 engine cover sub-assembly to detach the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to detach the clip and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to detach both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.




b.

for RHD:

i.
A434188

Lift the front of the No. 1 engine cover sub-assembly to detach the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to detach the clip and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to detach both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.




Hide 17750A 27.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 28.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide G92A0A 30.REMOVE INVERTER RESERVE TANK ASSEMBLY

a.
A434189C01
2.719,0.5 1.979,0.646 true 2.146,1.021 2.594,1.021 true 0.896,3.24 0.396,3.104 true 1.135,3.156 0.542,2.854 true 0.24,2.99 0.458,3.167 0.219,0.177 10 true *1 0.354,2.719 0.563,2.896 0.208,0.177 10 true *2 1.823,0.552 2.063,0.75 0.24,0.198 10 false *a 1.979,0.927 2.219,1.125 0.24,0.198 10 false *b
*1 No. 2 Inverter Cooling Hose
*2 No. 5 Inverter Cooling Hose
*a Pin
*b Grommet
V100135

Bolt
V100136

Clip


Remove the 2 bolts.


b.

Detach the pin and remove the inverter reserve tank assembly.


c.

Slide the 2 clips and disconnect the No. 2 inverter cooling hose and No. 5 inverter cooling hose from the inverter reserve tank assembly.


Hide 16282 31.REMOVE NO. 5 WATER BY-PASS HOSE

a.
A434190

Slide the 2 clips and remove the No. 5 water by-pass hose from the No. 3 water by-pass pipe and radiator assembly.


Hide 23826 32.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A434191

Detach the clamp.


b.

Disconnect the No. 1 fuel vapor feed hose from the purge VSV.


Hide 23901 33.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A434192

Remove the No. 1 fuel pipe clamp from the fuel tube connector.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Disconnect the fuel tube sub-assembly.

i.
A434193

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 87246 34.DISCONNECT OUTLET HEATER WATER HOSE

a.
A434194C01
0.938,1.76 1.688,1.573 true 0.729,1.667 0.958,1.844 0.229,0.177 10 true *a
*a Retainer
V113147

Pull out
V113148

Pull off


Pull out the retainer to detach the lock claws and pull off the outlet heater water hose from the No. 2 water by-pass pipe sub-assembly.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector with plastic bags to prevent damage and contamination.


Hide 87245 35.DISCONNECT INLET HEATER WATER HOSE

a.
A434195C01
0.563,1.76 1.313,1.573 true 0.396,1.688 0.625,1.865 0.229,0.177 10 true *a
*a Retainer
V113147

Pull out
V113148

Pull off


Pull out the retainer to detach the lock claws and pull off the inlet heater water hose from the flow shutting valve (water by-pass hose assembly).


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater water hose connector with plastic bags to prevent damage and contamination.


Hide 16571C 36.DISCONNECT NO. 1 RADIATOR HOSE

a.
A434196

Detach the clamp.


b.

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 37.DISCONNECT NO. 2 RADIATOR HOSE

a.
A434197

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 88711 38.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88704 39.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide G9229A 40.DISCONNECT NO. 5 INVERTER COOLING HOSE

a.
A434198

Slide the clip and disconnect the No. 5 inverter cooling hose from the motor cooling cooler.


Hide 41.DISCONNECT WIRE HARNESS

HINT:

After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.


a.
A434199

Detach the claws and remove the No. 2 relay block cover.


b.
A434201C01
0,0 0,0 false
V100135

Nut
V100136

Connector


Remove the nut from the engine room relay block and junction block assembly.


c.

Disconnect the connectors from the engine room relay block and junction block assembly.


d.

Using a screwdriver, detach the claw and disconnect the wire harness from the engine room relay block and junction block assembly.


e.
A434200

Detach the clamp.


f.

Remove the 2 bolts and disconnect the ground wires.


Hide 51468B 42.REMOVE ENGINE UNDER COVER HEAT INSULATOR

a.
A434184

Remove the 2 clips and engine under cover heat insulator.


Hide 58166A 43.REMOVE FRONT FLOOR COVER LH

a.
A434204C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Clip


Remove the 2 bolts, 4 screws and clip.


b.

Detach the clips and remove the front floor cover LH.


Hide 58165C 44.REMOVE FRONT FLOOR COVER RH

a.
A434203C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Clip


Remove the 2 bolts, 3 screws and clip.


b.

Detach the clips and remove the front floor cover RH.


Hide 17410 45.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 43502H 46.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 47.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 89543 48.DISCONNECT FRONT SPEED SENSOR LH

Hide 89542 49.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 50.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 51.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 52.DISCONNECT TIE ROD ASSEMBLY LH

Hide 45460 53.DISCONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 54.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 55.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45220 58.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 59.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

A457674C01
0,0 0,0 false
V113146

Attachments - -


NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.




b.
A434205C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A434206

Remove the 3 bolts and the engine mounting stay LH from the engine mounting insulator sub-assembly LH.


d.
A434207

Remove the 4 bolts and separate the engine mounting insulator sub-assembly LH from the hybrid vehicle transaxle assembly.


e.
A434208C01
0.885,1.021 1.156,0.5 true 2.469,0.969 2.219,0.396 true 0.948,4.292 0.521,4.292 true 2.99,4.281 2.563,4.281 true 0.208,2.833 0.375,3.01 0.167,0.177 10 true A 0.375,0.24 0.531,0.438 0.156,0.198 10 true B 2.927,0.25 3.083,0.448 0.156,0.198 10 true B 1.385,4.208 1.531,4.385 0.146,0.177 10 true C 0.531,3.917 0.688,4.094 0.156,0.177 10 true D 2.063,0.25 2.281,0.417 0.219,0.167 10 true *1 1.083,0.323 1.313,0.51 0.229,0.188 10 true *2 2.969,4.167 3.177,4.323 0.208,0.156 10 true *3 0.344,4.208 0.542,4.365 0.198,0.156 10 true *4 3.094,2.792 3.26,2.969 0.167,0.177 10 true A 1.969,4.208 2.115,4.385 0.146,0.177 10 true C 0.563,4.469 0.719,4.646 0.156,0.177 10 true D 2.813,3.885 2.969,4.063 0.156,0.177 10 true D 2.771,4.448 2.927,4.625 0.156,0.177 10 true D
*1 Front Bumper Extension Sub-assembly LH
*2 Front Bumper Extension Sub-assembly RH
*3 Rear Front Suspension Member Brace LH
*4 Rear Front Suspension Member Brace RH
V100135

Bolt
V100136

Nut


Remove the 2 bolts (A), 2 bolts (B), 4 nuts and front bumper extension sub-assembly LH and front bumper extension sub-assembly RH from the front frame assembly and vehicle body.


f.

Remove the 2 bolts (C), 4 bolts (D) and rear front suspension member brace LH and rear front suspension member brace RH from the front frame assembly and vehicle body.


g.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 23825 60.REMOVE FUEL DELIVERY GUARD

a.
A406670

Remove the bolt and fuel delivery guard from the engine mounting bracket RH.


Hide 61.INSTALL ENGINE HANGERS

a.
A406671C02
0.406,0.375 0.563,0.375 0.563,0.375 0.854,0.792 true 2.115,0.292 2.281,0.292 2.281,0.292 2.396,0.49 true 0.208,0.313 0.521,0.51 0.313,0.198 10 false *1 1.854,0.219 2.104,0.427 0.25,0.208 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 11361J 62.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A402190

Remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 51100H 63.REMOVE FRONT FRAME ASSEMBLY

Hide 12361 64.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>REMOVAL

Hide 82715 65.REMOVE WIRING HARNESS CLAMP BRACKET

a.

for LHD:

i.
A434209

Detach the clamps and disconnect the engine wire.


ii.

Remove the bolt and wiring harness clamp bracket.



b.

for RHD:

i.
A434210

Detach the clamp and disconnect the engine wire.


ii.

Remove the bolt and wiring harness clamp bracket.



Hide 12371A 66.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.

for LHD:

i.
A434211

Detach the clamp and disconnect the engine wire.


ii.

Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.



b.

for RHD:

i.
A434212

Detach the clamp and disconnect the engine wire.


ii.

Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.



Hide 82121 67.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 821H2 68.REMOVE HV AIR CONDITIONING WIRE

a.
A407269

Detach the clamps.


b.
A407267C02
1.167,0.563 1.417,0.302 1.417,0.302 1.573,0.302 true 1.625,0.229 1.938,0.427 0.313,0.198 10 false *a
*a Green-colored Lock
V100137

Slide


Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



c.

for 2WD:

i.
C379387

Remove the bolt.


ii.

Detach the guide to remove the HV air conditioning wire from the hybrid vehicle transaxle assembly.



d.

for 4WD/AWD:

i.
A444947

Remove the 2 bolts.


ii.

Detach the guide to remove the HV air conditioning wire from the hybrid vehicle transaxle assembly.



Hide 11363A 70.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 30900 71.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 72.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 19315 74.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 75.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 76.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


Hide G921A 77.REMOVE NO. 1 INVERTER RESERVE TANK BRACKET

a.
A434213

Remove the bolt and No. 1 inverter reserve tank bracket.


Hide 12305 78.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A434214C01
2.177,0.792 2.313,0.448 true 2.063,1.635 2.063,1.01 true 1.969,1.635 2.177,1.813 0.208,0.177 10 true *1 2.229,0.281 2.458,0.448 0.229,0.167 10 true *2
*1 Suction Pipe Sub-assembly
*2 Air Conditioning Tube And Accessory Assembly


Disconnect the connector.


b.

Detach the clamps and disconnect the suction pipe sub-assembly and air conditioning tube and accessory assembly.


c.
A434215C01
0,0 0,0 false
V100135

No. 6 Water By-pass Hose
V100136

Bolt
V100137

Nut


Disconnect the No. 6 water by-pass hose and detach the clamp.


d.

Remove the bolt and nut.


e.
A434216

Detach the clamps and remove the radiator reserve tank assembly.


f.
A434217

Remove the bolt and disconnect the No. 2 ground wire.


g.
A434218C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts and nut and remove the engine mounting insulator sub-assembly RH.


Hide 12341 79.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A434219

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12306 81.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.


a.
A434220

Remove the bolt.


b.

Detach the claw and disconnect the engine room main wire.


c.
A434221C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, nut and the engine mounting insulator sub-assembly LH.