Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD) › from 2020.08
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0377460 HOOD LOCK CONTROL CABLE ASSEMBLY(for LHD) A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY(for LHD)  REMOVAL  


PROCEDURE

Hide 17750A 1.REMOVE AIR CLEANER INLET ASSEMBLY (for Gasoline Model)

Hide 53510 2.REMOVE HOOD LOCK ASSEMBLY

a.
B521975C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


w/ Courtesy Switch:

i.

Disconnect the connector.



b.

Remove the 3 bolts.


c.
B521976

Detach the clamp and disconnect the hood lock control cable assembly to remove the hood lock assembly.

NOTICE:

Do not bend the hood lock control cable assembly excessively.



Hide 53601 3.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B521977C02
1.469,2.906 1.531,3.031 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Detach the claw in the direction (1) indicated by the arrow shown in the illustration.


b.

Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the hood lock control lever sub-assembly.


c.
B521978

Detach the clamp and remove the hood lock control lever sub-assembly from the hood lock control cable assembly.


Hide 4.REMOVE FRONT WHEEL

Hide 53896B 5.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH (for Long Type)

a.
B521979

Remove the 4 screws.


b.

Detach the claw and remove the front fender front splash shield LH.


Hide 53896B 6.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH (for Short Type)

a.
B522058

Remove the 3 screws.


b.

Detach the claw and remove the front fender front splash shield LH.


Hide 76622D 7.REMOVE FRONT FENDER MUDGUARD LH (w/ Mudguard)

Hide 75602A 9.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH (except Off Road Package)

Hide 75602A 10.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH (for Off Road Package)

Hide 53876A 11.REMOVE FRONT FENDER LINER LH

a.

w/ Mudguard:

i.

Remove the 8 clips and 2 screws.

B521981C02
2.771,3.75 3.042,3.969 0.271,0.219 12 true *A
*A w/o Mudguard - -
V100135

Clip
V100136

Screw




b.

w/o Mudguard:

i.

Remove the 9 clips and 2 screws.



c.
B521982

Using a screwdriver with its tip wrapped with protective tape, detach the claw and remove the 4 grommets.


d.

Remove the front fender liner LH.


Hide 53630 12.REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY

a.
B277362C22
1.896,1.135 2.396,1.135 true 1.729,1.083 2.042,1.323 0.313,0.24 10 false *a
*a String


Tie a string to the end of the hood lock control cable assembly in the cabin.

HINT:

Use a length of string long enough to pass through the engine compartment.



b.
B521983C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the grommet as shown in the illustration.


c.

Using a screwdriver with its tip wrapped with protective tape, detach the clamp and remove the hood lock control cable assembly.

B521984C01
1.49,4.094 1.865,4.344 true 0.917,1.854 1.396,2.052 true 2.375,1.24 2.833,1.354 true 4,1.063 4.521,1.313 true 5.906,1.615 6.406,1.458 true 1.948,4.323 2.135,4.5 0.188,0.177 10 true *1 0.719,1.76 0.906,1.938 0.188,0.177 10 true *1 2.865,1.25 3.052,1.427 0.188,0.177 10 true *1 4.573,1.219 4.76,1.396 0.188,0.177 10 true *1 5.74,1.531 5.927,1.708 0.188,0.177 10 true *1
*1 Hood Lock Control Cable Assembly - -



d.

Pull the hood lock control cable assembly into the engine room.

HINT:

Do not pull off the string, because it is used during installation. Leave it on the vehicle.



e.

Disconnect the string from the hood lock control cable assembly.