Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM3620E _51 Engine / Hybrid System _076500 M20A-FKS ENGINE MECHANICAL _0372441 ENGINE ASSEMBLY A

M20A-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Vehicle Identification Number (VIN) registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart entry and start system (for Entry Function)

·

smart entry and start system (for Start Function)

·

Steering lock function


for K120, K120F:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Front exhaust pipe assembly*2 GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Replacement of continuously variable transaxle assembly
for K120, K120F:
·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)
Replacement of CVT fluid Air bleed oil pump with motor assembly Stop and start system (Click here)
ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for K120:(Click here)
for K120F:(Click here)
Replacement of front bumper assembly
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.SECURE STEERING WHEEL

Hide 7.REMOVE FRONT WHEELS

Hide 53895B 8.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

a.
A434181

Remove the 3 screws.


b.

Detach the clip and remove the front fender front splash shield RH.


Hide 53896B 9.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

a.
A434180

Remove the 3 screws.


b.

Detach the clip and remove the front fender front splash shield LH.


Hide 51441 10.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the 2 bolts and 10 screws detach the guide and No. 1 engine under cover.

A434182C02
5.229,2.302 5.542,2.51 0.313,0.208 10 false .
V100135

Bolt
V100136

Screw



Hide 58165C 11.REMOVE FRONT FLOOR COVER RH (w/ Cover)

Hide 58166A 12.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58398F 13.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 58399D 14.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 51420 15.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

A433068C01
0,0 0,0 false
V100135

Screw
V100136

Bolt


a.

Remove the 2 bolts, 2 screws, 6 clips and No. 2 engine under cover assembly.


Hide 53737D 16.REMOVE FRONT FENDER APRON SEAL LH

a.
A434185C02
2.719,1.354 2.875,1.552 0.156,0.198 10 false .
V100135

Bolt
V100136

Clip


Remove the 2 bolts, clip and front fender apron seal LH.


Hide 53736E 17.REMOVE FRONT FENDER APRON SEAL RH

a.
A434186C02
2.99,1.042 3.146,1.24 0.156,0.198 10 false .
V100135

Bolt
V100136

Clip


Remove the 2 bolts, clip and front fender apron seal RH.


Hide 52618 19.REMOVE FRONT LOWER BUMPER ABSORBER

a.
A431799

Remove the 5 bolts.


b.

Detach the 2 claws to remove the front lower bumper absorber.


Hide 22.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 24.DRAIN TRANSFER OIL (for 4WD/AWD)

Hide 12601B 25.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A433072

Lift the front of the No. 1 engine cover sub-assembly to detach the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to detach the clip and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to detach both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide 17750A 26.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 27.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 29.REMOVE BATTERY

Hide 74404B 30.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A433073

Detach the 2 clamps from the battery clamp sub-assembly.


b.
A433074C01
0.885,0.99 1.083,0.99 1.083,0.99 1.26,1.208 true 2.208,1.104 2.5,0.875 2.5,0.875 2.688,0.875 true 1.271,0.115 1.469,0.115 1.469,0.115 1.646,0.333 true 0.635,0.906 0.875,1.094 0.24,0.188 10 true *1 2.698,0.792 2.917,0.979 0.219,0.188 10 true *2 1.052,0.031 1.271,0.24 0.219,0.208 10 true *3
*1 No. 2 Engine Wire
*2 Engine Room Main Wire
*3 Positive (+) Battery Terminal


Detach the 2 clamps and disconnect the engine room main wire and No. 2 engine wire from the battery clamp sub-assembly.


c.

Remove the nut and disconnect the engine room main wire and No. 2 engine wire from the positive (+) battery terminal.


d.

Detach the 2 claws and disconnect the engine room main wire from the No. 2 engine wire.


e.
A433075

Remove the 3 bolts and battery clamp sub-assembly.


Hide 33820B 31.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)

a.
A433078C01
1.719,2.708 1.885,2.531 1.885,2.531 2.083,2.531 false 2.115,2.438 2.427,2.594 0.313,0.156 10 false *a 3.021,3.396 3.333,3.552 0.313,0.156 10 false *b
*a Clip
*b 45° to 60°


While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


b.

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 33820B 32.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.
A433071

Remove the 4 clips and disconnect the 2 transmission control cables.


Hide 23826 33.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A433081

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve assembly.


Hide 44773F 34.DISCONNECT UNION TO CHECK VALVE HOSE

a.
A433080

Detach the clamp.


b.

Disconnect the union to check valve hose from the vacuum pump assembly.


Hide 87246 35.DISCONNECT OUTLET HEATER WATER HOSE

a.
A433082C01
1.958,1.906 1.948,1.667 1.948,1.667 1.677,1.594 true 1.865,1.906 2.177,2.063 0.313,0.156 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to detach the lock claws and pull off the outlet heater water hose.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector with plastic bags to prevent damage and contamination.


Hide 87245 36.DISCONNECT INLET HEATER WATER HOSE

a.
A433083C01
0.885,1.198 1.135,1.198 1.135,1.198 1.323,1.552 true 0.656,1.125 0.875,1.344 0.219,0.219 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to detach the lock claws and pull off the inlet heater water hose.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater water hose connector with plastic bags to prevent damage and contamination.


Hide 23901 37.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A433086

Remove the No. 1 fuel pipe clamp from the fuel tube connector.


b.

Disconnect the fuel tube sub-assembly.

i.
A433087

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 16571C 38.DISCONNECT NO. 1 RADIATOR HOSE

a.
A433089

Remove the clamp to disconnect the No. 1 radiator hose from the No. 1 radiator bracket.


b.

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 39.DISCONNECT NO. 2 RADIATOR HOSE

a.

Detach the radiator hose clamp from the fan shroud.


b.
A433088

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 88704 40.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 41.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 42.DISCONNECT WIRE HARNESS

HINT:

After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.


a.
A433095

Detach the 3 claws.


b.

Remove the No. 2 relay block cover from the engine room relay block and junction block assembly.


c.
A433094C01
1.344,2.385 1.5,2.583 0.156,0.198 10 false .
V100135

Nut
V100136

Connector


Remove the nut from the engine room relay block and junction block assembly.


d.

Disconnect the 5 connectors from the engine room relay block and junction block assembly.


e.

Using a screwdriver, detach the claw and separate the wire harness from the engine room relay block and junction block assembly.


f.

for CVT:

i.
A433076

Detach the clamp.


ii.

Remove the bolt and disconnect No. 3 engine wire from the CVT transaxle assembly.



g.

for Manual Transaxle:

i.
A433079

Detach the clamp.


ii.

Remove the bolt and disconnect No. 3 engine from the manual transaxle assembly.



h.
A433096

Detach the clamp.


i.

Remove the bolt and disconnect the wire harness from the vehicle body.


Hide 16282 43.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
A433098

Slide the 2 clips and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.


Hide 45220 44.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 17410 45.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 43502H 46.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 47.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 48.DISCONNECT FRONT SPEED SENSOR LH

Hide 49.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 50.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 51.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 52.DISCONNECT TIE ROD ASSEMBLY LH

Hide 45460 53.DISCONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 54.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48069 55.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 31481A 59.DISCONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)

a.
A433077

Using a 10 mm union nut wrench, disconnect the clutch hose from the accumulator to flexible hose tube.


b.

Remove the clip and disconnect the clutch hose.


Hide 37117 60.REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD/AWD)

Hide 37110 61.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)

Hide 62.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

A457673C02
0,0 0,0 false
V113146

Attachments - -


NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.




b.
A433097C01
2.5,1.229 2.656,1.427 0.156,0.198 10 false .
V100135

Bolt
V100136

Nut


Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A433100

for CVT:

Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.


d.
A433735

for Manual Transaxle:

Remove the bolt and nut and separate the engine mounting bracket LH from the transverse engine engine mounting insulator.


e.
A433102C01
1.979,1.75 2.198,1.75 2.198,1.75 2.396,1.333 true 1.438,1.75 1.208,1.75 1.208,1.75 1.021,1.458 true 1.99,4.563 2.208,4.563 2.208,4.563 2.313,4.313 true 1.438,4.542 1.208,4.542 1.208,4.542 1.073,4.302 true 1.01,0.844 1.167,1.042 0.156,0.198 10 false . 0.354,2.948 0.51,3.146 0.156,0.198 10 true A 3,2.927 3.156,3.125 0.156,0.198 10 true A 1.073,1.063 1.229,1.26 0.156,0.198 10 true B 2.292,0.99 2.448,1.188 0.156,0.198 10 true B 1.5,4.229 1.656,4.427 0.156,0.198 10 true C 1.771,4.24 1.927,4.438 0.156,0.198 10 true C 0.406,4.021 0.563,4.219 0.156,0.198 10 true D 0.438,4.417 0.594,4.615 0.156,0.198 10 true D 2.875,4.042 3.031,4.24 0.156,0.198 10 true D 2.844,4.417 3,4.615 0.156,0.198 10 true D 1.792,1.656 1.948,1.854 0.156,0.198 10 false *1 1.49,1.656 1.646,1.854 0.156,0.198 10 false *2 1.76,4.469 1.979,4.656 0.219,0.188 10 true *3 1.458,4.448 1.656,4.667 0.198,0.219 10 true *4
*1 Front Bumper Extension Sub-assembly LH
*2 Front Bumper Extension Sub-assembly RH
*3 Rear Front Suspension Member Brace LH
*4 Rear Front Suspension Member Brace RH
V100135

Bolt
V100136

Nut


Remove the 2 bolts (A), 2 bolts (B), 4 nuts and front bumper extension sub-assembly LH and front bumper extension sub-assembly RH from the front frame assembly and vehicle body.


f.

Remove the 2 bolts (C), 4 bolts (D) and rear front suspension member brace LH and rear front suspension member brace RH from the front frame assembly and vehicle body.


g.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 89481B 63.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ GPF)

Hide 25760 64.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY (w/ GPF)

Hide 25706 65.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)

Hide 17167 66.SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 23825 69.REMOVE FUEL DELIVERY GUARD

a.
A402191

Remove the bolt and fuel delivery guard from the engine mounting bracket RH.


Hide 70.INSTALL ENGINE HANGERS

a.
A402192C01
0.479,0.542 0.656,0.542 0.656,0.542 0.885,0.854 true 2.313,0.25 2.49,0.25 2.49,0.25 2.719,0.563 true 2.063,0.177 2.281,0.365 0.219,0.188 10 true *2 0.25,0.438 0.458,0.635 0.208,0.198 10 true *1
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 11361J 71.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A402190

Remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 32101A 72.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)

Hide 73.DISCONNECT VACUUM HOSE (w/ Active Control Engine Mount)

Hide 16261G 74.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 16260 75.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

Hide 45319 76.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 12361 81.REMOVE FRONT ENGINE MOUNTING INSULATOR (for Manual Transaxle)

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.



Hide 12371A 82.REMOVE REAR ENGINE MOUNTING INSULATOR (for Manual Transaxle)

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.



Hide 12311A 83.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
A433106C01
0.052,0.042 0.365,0.198 0.313,0.156 10 false *A 0.042,2.375 0.354,2.531 0.313,0.156 10 false *B
*A for CVT
*B for Manual Transaxle


Remove the 3 bolts and front engine mounting bracket from the transaxle housing.


Hide 30300 86.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 30400 87.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 88.FIX ENGINE ASSEMBLY

a.

Using wooden blocks or plate lift attachments, set the engine on a flat surface.

NOTICE:
·

Place wooden blocks or plate lift attachments so that the engine is level.

·

Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.

·

Perform this step while supporting the engine assembly using a sling device and chain block.




Hide 31210 89.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31250 90.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31400 91.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY (for Manual Transaxle)

Hide 13405 92.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 32101 93.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 19315 94.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 82121 95.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 96.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 97.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


Hide 12305 98.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A433177

Disconnect the No. 6 water by-pass hose.


b.

Detach the clamp.


c.
A429127

Detach the clamps and disconnect the suction pipe sub-assembly and air conditioning tube and accessory assembly.


d.
A429129

Remove the bolt, nut and the radiator reserve tank assembly.


e.
A433101

Remove the bolt and disconnect the No. 2 ground wire from the engine mounting insulator sub-assembly RH.


f.
A433179C01
2.625,1.26 2.781,1.458 0.156,0.198 10 false .
V100135

Bolt
V100136

Nut


Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH.


Hide 12341 99.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A433180

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12372A 100.REMOVE ENGINE MOUNTING INSULATOR LH (for CVT)

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A433181

Remove the 4 bolts and rear engine mounting insulator LH from the vehicle body.


Hide 12371A 101.REMOVE ENGINE MOUNTING BRACKET LH (for Manual Transaxle)

HINT:

Perform this procedure only when replacement of the engine mounting bracket LH is necessary.


a.
A433182

Remove the bolt from the flexible hose bracket.


b.

Remove the 4 bolts and engine mounting bracket LH from the vehicle body.